DMC:V2500-00-70-38-34-00A-081A-D|Issue No:001|Issue Date:2013-03-20

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 70-38-34-100-501 The Make-Up Of Stoving Primer And Enamel (Epoxy Type)

NOTE

To identify the consumable materials, refer to the PCI.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

Name	Manufacturer	Part Number / Identification
CoMat 02-019 TAPE, ADHESIVE PAPER HEAT RESISTING MASKING	94960	CoMat 02-019
CoMat 05-020 WATERPROOF SILICON CARBIDE	LOCAL	CoMat 05-020
CoMat 05-021 WATERPROOF SILICON CARBIDE	44197	CoMat 05-021
CoMat 07-062 TWO-PACK EPOXY FINISH, GREY, AIRCRAFT, BS381C 693	LOCAL	CoMat 07-062
CoMat 07-080 TWO-PACK EPOXY PRIMER AND CATALYST	LOCAL	CoMat 07-080
CoMat 07-081 EPOXY PRIMER CATALYST	0AM53	CoMat 07-081
CoMat 07-082 THINNER	LOCAL	CoMat 07-082
CoMat 07-086 CHROMATE EPOXY PRIMER	LOCAL	CoMat 07-086
CoMat 07-087 EPOXY ENAMEL GREY	LOCAL	CoMat 07-087
CoMat 07-088 THINNER	LOCAL	CoMat 07-088

Spares

NONE

Safety Requirements

WARNING

IT IS THE RESPONSIBILITY OF THE OPERATOR TO OBTAIN AND OBSERVE THE MANUFACTURERS MATERIAL SAFETY DATA SHEETS FOR CONSUMABLE MATERIALS INFORMATION SUCH AS, HAZARDOUS INGREDIENTS, PHYSICAL/CHEMICAL CHARACTERISTICS, FIRE, EXPLOSION, REACTIVITY, HEALTH HAZARD DATA, PRECAUTIONS FOR SAFE HANDLING, USE AND CONTROL MEASURES AND ALSO TO TAKE LOCAL REGULATIONS INTO CONSIDERATION.

Procedure

1. Stir each pigmented base fully until equally mixed.
2. Fully mix together the applicable base and catalyst and add the applicable thinners as necessary. Allow the mixture to stand for 30 minutes before application, the pot life is approximately 8 hours, all primer or enamel not used within this time must be discarded.
3. The viscosity of the heat curing CoMat 07-086 CHROMATE EPOXY PRIMER and CoMat 07-087 EPOXY ENAMEL GREY must be 24 to 26 seconds, B.S.3900 flow cup type B4 at 68 deg F (20 deg C) immediately before use. Thin as necessary using CoMat 07-088 THINNER.

Requirements After Job Completion

Follow-On Conditions

NONE

Manufacturer Code:	0AM53
Enterprise Name:	IAE INTERNATIONAL AERO ENGINES AG
BU Name:	NULL
Building:	SUITE 400
Street:	628 HEBRON AVENUE
City:	GLASTONBURY
State:	CT
Zip Code:	06033
Country:	USA

Manufacturer Code:	44197
Enterprise Name:	SAINT-GOBAIN INDUSTRIAL CERAMICS INC.
BU Name:	SAINT-GOBAIN ABRASIVES, INC
Street:	ONE NEW BOND STREET
P.O. Box:	PO BOX 15008
City:	WORCESTER
State:	MA
Zip Code:	01615-0008
Country:	USA
Phone Number:	1-508-795-5000
Fax Number:	1-508-795-2828
Internet:	www.saint-gobain-northamerica.com

Manufacturer Code:	94960
Enterprise Name:	3M TRAFFIC CONTROL
BU Name:	3M TRAFFIC CONTROL
Department:	MATERIALS DIVISION
Building:	225 55
Street:	3M CENTER
City:	ST PAUL
State:	MN
Zip Code:	55144-1000
Country:	USA
Phone Number:	1-612-733-0477
Internet:	www.3m.com/tcm

Manufacturer Code:	LOCAL
Enterprise Name:	LOCALLY SUPPLIED

Manufacturer Code:

76381

Supply Number:

CoMat 02-019

Type:

sp01

Supply Name:

CoMat 02-019 TAPE, ADHESIVE PAPER HEAT RESISTING MASKING

Specification Groups:

Doc Number	Type
OMAT: 2/40 (RR REF)	SELLOTAPE 2595 SCAPA 2595 OR 3M HT214
JCR-201 (JAEC REF)	SELLOTAPE 2595 SCAPA 2595 OR 3M HT214

Suppliers:

Manufacturer	Remarks
76381
K3312
K6835

Manufacturer Code:

1E1X8

Supply Number:

CoMat 05-020

Type:

sp01

Supply Name:

CoMat 05-020 WATERPROOF SILICON CARBIDE

Specification Groups:

Doc Number	Type
OMAT: 5/33 (RR REF)	WATERPROOF SILICON CARBIDE ABRASIVE PAPER, CAMI GRIT DESIGNATION 320 (ANSI B74.18)
JCR-027 (JAEC REF)
JCR-186 (JAEC REF)

Suppliers:

Manufacturer	Remarks
1E1X8
LOCAL
K6835

Manufacturer Code:

1E1X8

Supply Number:

CoMat 05-021

Type:

sp01

Supply Name:

CoMat 05-021 WATERPROOF SILICON CARBIDE

Specification Groups:

Doc Number	Type
OMAT: 5/35 (RR REF)	WATERPROOF SILICON CARBIDE ABRASIVE PAPER, CAMI GRIT DESIGNATION 240 (ANSI B74.18 )
JCR-188 (JAEC REF)

Suppliers:

Manufacturer	Remarks
1E1X8
K6835
LOCAL

Manufacturer Code:

5HCF1

Supply Number:

CoMat 07-062

Type:

sp01

Supply Name:

CoMat 07-062 TWO-PACK EPOXY FINISH, GREY, AIRCRAFT, BS381C 693

Specification Groups:

Doc Number	Type
+	BASE EC75/693
OMAT: 789 (RR REF)	GLOSS CATALYST ACT 65 or MATT CATALYST ACT 68

Suppliers:

Manufacturer	Remarks
5HCF1
K5635
K6835

Manufacturer Code:

5HCF1

Supply Number:

CoMat 07-080

Type:

sp01

Supply Name:

CoMat 07-080 TWO-PACK EPOXY PRIMER AND CATALYST

Specification Groups:

Doc Number	Type
+	BASE COMPONENT PR 143
OMAT:766 (RR REF)	CATALYST ACT 149

Suppliers:

Manufacturer	Remarks
5HCF1
K5635
K6835

Manufacturer Code:

0AM53

Supply Number:

CoMat 07-081

Type:

sp01

Supply Name:

CoMat 07-081 EPOXY PRIMER CATALYST

Specification Groups:

Doc Number	Type
	DELETED

Suppliers:

Manufacturer	Remarks
0AM53

Manufacturer Code:

5HCF1

Supply Number:

CoMat 07-082

Type:

sp01

Supply Name:

CoMat 07-082 THINNER

Specification Groups:

Doc Number	Type
OMAT: 793 (RR REF)	T17
JCR-271 (JAEC REF)

Suppliers:

Manufacturer	Remarks
5HCF1
K5635
K6835

Manufacturer Code:

K3504

Supply Number:

CoMat 07-086

Type:

sp01

Supply Name:

CoMat 07-086 CHROMATE EPOXY PRIMER

Specification Groups:

Doc Number	Type
	588/0060/3

Suppliers:

Manufacturer	Remarks
K3504
K6835

Manufacturer Code:

X222X

Supply Number:

CoMat 07-087

Type:

sp01

Supply Name:

CoMat 07-087 EPOXY ENAMEL GREY

Specification Groups:

Doc Number	Type
	DELETED

Suppliers:

Manufacturer	Remarks
X222X

Manufacturer Code:

X222X

Supply Number:

CoMat 07-088

Type:

sp01

Supply Name:

CoMat 07-088 THINNER

Specification Groups:

Doc Number	Type
	DELETED

Suppliers:

Manufacturer	Remarks
X222X

TASK 70-38-34-100-501 The Make-Up Of Stoving Primer And Enamel (Epoxy Type)

Export Control

Copyright

Applicability

Common Information

TASK 70-38-34-100-501 The Make-Up Of Stoving Primer And Enamel (Epoxy Type)

NOTE

Preliminary Requirements

Pre-Conditions

Support Equipment

Consumables, Materials and Expendables

Spares

Safety Requirements

WARNING

Procedure

SUBTASK 70-38-34-100-001 Make-up of the Stoving Primer and Enamel

Requirements After Job Completion

Follow-On Conditions