TASK 71-00-02-000-017 (A1/A5-PPBU) - Remove The Pneumatic Starter And Housing Adapter, Removal-017

DMC:V2500-A0-71-00-0200-16A-520A-B|Issue No:001.00|Issue Date:2013-11-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 71-00-02-000-017 (A1/A5-PPBU) - Remove The Pneumatic Starter And Housing Adapter, Removal-017

General

Fig/item numbers in parenthesis in the procedure agree with those used in the IPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the IPC.

For all parts identified in a different Chapter/Section/Subject, the applicable Chapter/Section/Subject comes before the Fig/item number.

Apply the approved CoMat 10-058 PENETRATING OIL before the removal of threaded parts. Let the parts soak before removal.

Remove and discard the lockwire before the tube or connector is disconnected.

Seal all openings to prevent contamination from unwanted materials.

Discard all rubber seal rings removed in this procedure.

NOTE

To identify the consumable materials refer to the PCI.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 10-058 PENETRATING OIL0AM53CoMat 10-058

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 71-00-02-050-005 Remove the Pneumatic Starter and Housing Adapter

    1. Refer to Figure.

    2. Position an applicable container, remove the combined drain plug/magnetic chip detector and drain the pneumatic starter. Remove and discard the preformed packing from the drain plug.

    3. WARNING

      BE CAREFUL WHEN YOU REMOVE THE PNEUMATIC STARTER BECAUSE IT WEIGHS 33 LB (15KG).

      NOTE

      The pneumatic starter must have its maintenance completed, as given in the Sumitomo Component Maintenance Manual (80-13-41).

      Hold the starter and remove the clamp that attaches it to the housing adapter. Move the starter forward to disengage the splines and remove the starter. Remove the preformed packing from the starter drive shaft.

    4. Remove the six nuts STARTING-PNEUMATIC STARTER (80-13-41, 01-106) that attach the housing adapter STARTING-PNEUMATIC STARTER (80-13-41, 01-260) to the mounting pad.

    5. Remove the housing adapter STARTING-PNEUMATIC STARTER (80-13-41, 01-260).

    6. Install the applicable blanks to the starter and to the external gearbox.

    2. Figure: Remove the Pneumatic Starter

    Remove the Pneumatic Starter

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:X222X
Supply Number:CoMat 10-058
Type:sp01
Supply Short Name:CoMat 10-058 PENETRATING OIL
Supply Name:CoMat 10-058 PENETRATING OIL
Suppliers:
ManufacturerRemarks
X222X