TASK 72-32-00-430-015 LPC/Intermediate Case Module - Move The LPC/Intermediate Case Module From The Turnover Stand To The Storage Stand, Assembly-015

DMC:V2500-A0-72-32-0000-15A-710A-B|Issue No:001.00|Issue Date:2013-11-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-32-00-430-015 LPC/Intermediate Case Module - Move The LPC/Intermediate Case Module From The Turnover Stand To The Storage Stand, Assembly-015

General

Fig/item numbers in parentheses in the procedure agree with those used in the IPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the IPC.

For all parts identified in a different Chapter/Section/Subject, the applicable Chapter/Section/Subject comes before the Fig/item number.

This TASK gives the procedure to move the LP compressor/intermediate case module from the turnover stand to the storage stand.

NOTE

Special tools are identified in the procedure by the tool primary number.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NameManufacturerPart Number / IdentificationQuantityRemark
IAE 1J12010 Storage stand0AM53IAE 1J120101
IAE 1J12487 Rear sling0AM53IAE 1J124871

Consumables, Materials and Expendables

NONE

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-32-00-430-182 Install the Rear Sling on to the LP Compressor/Intermediate Case Module

    1. Refer to Figure.

    2. Make sure that the LP compressor/intermediate case module is installed, vertically with the rear end up, on the turnover stand. Refer to TASK 72-32-00-430-014 (ASSEMBLY-014).

    3. Attach a hoist to IAE 1J12487 Rear sling 1 off.

    4. Move the rear sling adjacent to the fan frame rear flange of the module.

    5. Align the 20 holes in the lift sling (part of the rear sling) with the 20 holes in the fan frame rear flange.

    6. Attach the lift sling to the fan frame rear flange and safety with 20 bolts and the four ring supports (part of the rear sling). Tighten the bolts.

    2. SUBTASK 72-32-00-430-183 Move the Module from the Turnover Stand to the Storage Stand

    1. Refer to Figure and Figure.

    2. Adjust the hoist to make the hoist rope/chain tighter.

    3. Remove the four bolts and washers which attach the plate to each of the supports A and B of the turnover stand, Figure.

    4. Remove the two plates from the supports A and B.

    5. Slowly lift the module to disengage each square rod end of the brackets A and B from each slot in the supports A and B.

    6. Move and install the module to IAE 1J12010 Storage stand 1 off, Figure.

    3. SUBTASK 72-32-00-430-184 Remove the Brackets A and B and the two Adapters from the Module

    1. Refer to Figure.

    2. Remove the four bolts and washers which attach each of the brackets A and B to the adapter.

    3. Remove the two bolts and nuts which attach each adapter to the fan case flanges FD and FE.

    4. Remove the two adapters from the fan case.

    4. SUBTASK 72-32-00-430-185 Remove the Rear Sling from the Module

    1. Refer to Figure.

    2. Remove the 20 bolts and the four ring stoppers which attach the lift sling of the rear sling to the fan frame rear flange of the module.

    3. Lift and remove the rear sling from the fan frame rear flange. Move the rear sling to the work bench.

    4. Remove the hoist from the rear sling.

    5. Figure: Install the rear sling on to the fan frame rear flange of the module

    Install the rear sling on to the fan frame rear flange of the module

    Figure: Remove the module from the turnover stand

    Remove the module from the turnover stand

    Figure: Install the module on to the storage stand and remove the rear sling from the module

    Install the module on to the storage stand and remove the rear sling from the module

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:0AM53
Tool Number:IAE 1J12010
Tool Name:IAE 1J12010 Storage stand
Manufacturer Code:0AM53
Tool Number:IAE 1J12487
Tool Name:IAE 1J12487 Rear sling