Export Control
EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.Copyright
© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).Applicability
All
Common Information
TASK 72-32-36-700-102 No. 3 Bearing Oil Feed Mid Tube - Do A Test, Testing-002
General
Fig/item numbers in parentheses in the procedure agree with those used in the IPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the IPC.
All test pressures referred to in the text are gage pressure.
NOTE
NOTE
The Test Equipment Specification
Hydraulic pressure test rig
Booster pump - 0 to 600 psi (0 to 4140 kPa)
Tank - 5.3 gallon (20 liter)
Gage - 0 to 600 psi (0 to 4140 kPa)
Dry compressed air supply
Air regulator - 0 to 143 psi (0 to 986 kPa)
Preliminary Requirements
Pre-Conditions
NONESupport Equipment
| Name | Manufacturer | Part Number / Identification | Quantity | Remark |
|---|---|---|---|---|
| IAE 2J12603 Fixture | 0AM53 | IAE 2J12603 | ||
| Hydraulic pressure testing rig | LOCAL | Hydraulic pressure testing rig | ||
| Dry compressed air supply | LOCAL | Dry compressed air supply |
Consumables, Materials and Expendables
| Name | Manufacturer | Part Number / Identification | Quantity | Remark |
|---|---|---|---|---|
| CoMat 10-039 ENGINE OIL | LOCAL | CoMat 10-039 |
Spares
NONESafety Requirements
NONEProcedure
Attach IAE 2J12603 Fixture 1 off to the tube.
Connect Dry compressed air supply to the fixture on the tube.
Put the tube in to a tank of water and pressurize to 14.5 psi (100 kPa).
Hold the pressure for a minimum of one minute while you examine the tube for signs of leakage, specially at swaged, brazed, welded, or repaired areas.
Isolate the air supply, release the pressure and remove the tube from the tank.
Remove the fixture and dry the tube with dry warm air if the hydraulic pressure test is not to be done immediately.
Put applicable covers on all openings of the tube and keep it in a clean container to prevent contamination.
SUBTASK 72-32-36-790-052 Do the Leak Test on the Oil Feed Tube Assembly
Attach IAE 2J12603 Fixture 1 off to the tube.
Connect Hydraulic pressure testing rig to the fixture on the tube.
Open the bleed valve and apply the minimum hydraulic pressure necessary to bleed air from the tube. Close the bleed valve when you see a fluid flow which has no air.
Slowly and continuously apply the specified pressure given in Step.
Hold the pressure for a minimum of two minutes while you examine the tube for signs of leakage, specially at swaged, brazed, welded or repaired areas.
Isolate the hydraulic supply, release the pressure and remove the test equipment from the tube.
SUBTASK 72-32-36-780-053 Do the Hydraulic Pressure Test on the Oil Feed Tube Assembly
WARNING
MAKE SURE THAT APPROVED SAFETY GUARDS ARE IN POSITION AROUND THE TUBES WHEN YOU APPLY HYDRAULIC PRESSURE.NOTE
The leak test given in Step, must be completed before you do the hydraulic pressure test.NOTE
Do the hydraulic pressure test with CoMat 10-039 ENGINE OIL or equivalents.Clean the tube after the pressure test. Refer to the cleaning procedure, Cleaning-000 TASK 72-32-36-100-100.
SUBTASK 72-32-36-110-055 Clean the Oil Feed Tube Assembly
Put applicable caps on all openings of the tube and keep it in a clean container to prevent contamination.
SUBTASK 72-32-36-550-052 Store the Oil Feed Tube Assembly