TASK 72-41-31-300-014 HPC Stage 3 Blanking Plug - Blend Repair, Repair-014 (VRS6288)

DMC:V2500-A0-72-41-3123-00A-649A-C|Issue No:001.00|Issue Date:2013-11-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-41-31-300-014 HPC Stage 3 Blanking Plug - Blend Repair, Repair-014 (VRS6288)

Effectivity

FIG/ITEM PART NO.

01-100

6A2330

Material of component

RR

DESCRIPTION SYMBOL MATERIAL

HP compressor stage 3

EAF

18/8 Stainless steel

borescope blank

General

This Repair must only be done when the instruction to do so is given in 72-41-31 Inspection-xxx.

This Repair has been issued for the HP compressor stage 3 borescope blank surface damage.

The practices and processes referred to in the procedure by the TASK number are in the SPM.

Price and availability - none

NOTE

  1. Equivalent materials or equipment can be used.

  2. More equipment and materials necessary to do this Repair are given in the SPM TASKS given below:

    TASK 70-23-01-230-501

    TASK 70-23-03-230-501

    TASK 70-35-03-300-501

NOTE

To identify the consumable materials refer to the PCI.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NameManufacturerPart Number / IdentificationQuantityRemark
Workshop inspection equipmentLOCALWorkshop inspection equipment
Penetrant Crack Test EquipmentLOCALPenetrant crack test equipment

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 05-106 ABRASIVE STONEK6835CoMat 05-106
CoMat 05-110 EMERY POLISHING PAPER0AM53CoMat 05-110
CoMat 05-111 EMERY POLISHING PAPER06565CoMat 05-111

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-41-31-230-073-001 Do a Crack Test

      1. Do a penetrant crack test.

      1. Refer to the SPM TASK 70-23-01-230-501.

        Cracks are not permitted.

    2. SUBTASK 72-41-31-230-073-002 Do a Crack Test

      1. Do a penetrant crack test.

      1. Refer to the SPM TASK 70-23-03-230-501.

        Cracks are not permitted.

    3. SUBTASK 72-41-31-350-066 Remove the Damage

    1. Refer to Figure.

      2. Remove small areas of damage as necessary.

      1. Make sure the damage marks are completely removed and the area is made smooth in to the adjacent material.

        The maximum depth to remove the damage must not be more than 0.005 in. (0.13 mm.).

        The diameter of the area removed is to be 50 times the depth.

        Refer to the SPM TASK 70-35-03-300-501.

      3. Blend the area of the repair.

      4. Polish the area of the repair.

      1. Polish the repaired area to remove the scratches and to give a surface finish the same as the adjacent material.

        Refer to the SPM TASK 70-35-03-300-501.

    4. SUBTASK 72-41-31-220-135 Examine the Repair

    1. Refer to Figure.

      2. Do a visual and dimensional inspection.

      1. Make sure the surface finish is the same as the adjacent material.

        The maximum depth of the repair must not be more than 0.005 in. (0.13 mm.).

        Use workshop inspection equipment.

    5. SUBTASK 72-41-31-230-074-001 Do a Crack Test

      1. Do a penetrant crack test.

      1. Refer to the SPM TASK 70-23-01-230-501.

        Cracks are not permitted.

    6. SUBTASK 72-41-31-230-074-002 Do a Crack Test

      1. Do a penetrant crack test.

      1. Refer to the SPM TASK 70-23-03-230-501.

        Cracks are not permitted.

    7. Figure: An example of an area to be repaired

    An example of an area to be repaired

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:06565
Enterprise Name:SAINT-GOBAIN ABRASIVES
BU Name:SAINT-GOBAIN ABRASIVES
P.O. Box:808
City:TROY
State:NY
Zip Code:12181
Country:USA
Phone Number:1-518-266-2200
Fax Number:1-518-266-2342
Internet:www.saintgobain.com
Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:K6835
Enterprise Name:MED-LAB LTD
BU Name:MED-LAB LTD
Street:COPELAND ST
City:DERBY
Zip Code:DE1 2PU
Country:GREAT BRITAIN
Phone Number:44-1332-349094
Fax Number:44-1332-371237
Email:sales@med-lab.co.uk
Internet:www.med-lab.co.uk
Manufacturer Code:LOCAL
Enterprise Name:LOCALLY SUPPLIED
Manufacturer Code:K6835
Supply Number:CoMat 05-106
Type:sp01
Supply Short Name:CoMat 05-106 ABRASIVE STONE
Supply Name:CoMat 05-106 ABRASIVE STONE
Specification Groups:
Doc NumberType
(SS-S-736/2/26) (A-A-3068/2-26)SQUARE FINE SS-S-736 TYPE II CLASS A1
Suppliers:
ManufacturerRemarks
K6835
KC1D9
Manufacturer Code:X111X
Supply Number:CoMat 05-110
Type:sp01
Supply Short Name:CoMat 05-110 EMERY POLISHING PAPER
Supply Name:CoMat 05-110 EMERY POLISHING PAPER
Specification Groups:
Doc NumberType
DISCONTINUED
Suppliers:
ManufacturerRemarks
X111X
Manufacturer Code:44197
Supply Number:CoMat 05-111
Type:sp01
Supply Short Name:CoMat 05-111 EMERY POLISHING PAPER
Supply Name:CoMat 05-111 EMERY POLISHING PAPER
Specification Groups:
Doc NumberType
FEPA GRIT SIZE P280 OR P240 EMERY POLISHING PAPER OR ALUMINUM OXIDE ABRASIVE PAPER
Suppliers:
ManufacturerRemarks
44197
K6835
KC1D9
LOCAL
Manufacturer Code:LOCAL
Tool Number:Penetrant crack test equipment
Tool Name:Penetrant Crack Test Equipment
Manufacturer Code:LOCAL
Tool Number:Workshop inspection equipment
Tool Name:Workshop inspection equipment