TASK 72-60-32-040-001 Angle Gearbox Support Assembly - Disassemble The Support, Disassembly-001

DMC:V2500-A0-72-60-3200-00A-530A-B|Issue No:001.00|Issue Date:2013-11-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-60-32-040-001 Angle Gearbox Support Assembly - Disassemble The Support, Disassembly-001

General

Fig/item numbers in parentheses in the procedure agree with those used in the IPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the IPC.

Apply the approved CoMat 10-058 PENETRATING OIL before the removal of the threaded parts and parts with an interference fit. Let the parts soak before removal.

Discard all rubber seal rings, cotter pins and seal washers removed in this procedure.

NOTE

To identify the consumable materials refer to the PCI.

NOTE

Special tools are identified in the procedure by the tool primary number.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NameManufacturerPart Number / IdentificationQuantityRemark
Puller0AM53IAE 1F101581
IAE 1F10169 Base, remove/install0AM53IAE 1F101691

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 10-058 PENETRATING OIL0AM53CoMat 10-058

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-60-32-040-051 Remove the Shrouds and the Outer Races from the Angle Gearbox Support

    1. Refer to Figure.

    2. Install the angle gearbox support on the plate of IAE 1F10169 Base, remove/install 1 off with the mounting flange of the angle gearbox to the top.

    3. Install the hexagon head capscrews which attach the angle gearbox support on the plate of the base.

    4. Remove the nut which attach the two shrouds and the two outer races of the roller bearings to the angle gearbox support.

    5. Remove the shrouds.

    6. Remove the outer races from the angle gearbox support. Use Puller 1 off.

    7. Release the hexagon head capscrews and remove the angle gearbox support from the base.

    2. Figure: Remove the shrouds and the outer races from the angle gearbox support

    Remove the shrouds and the outer races from the angle gearbox support

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:X222X
Supply Number:CoMat 10-058
Type:sp01
Supply Short Name:CoMat 10-058 PENETRATING OIL
Supply Name:CoMat 10-058 PENETRATING OIL
Suppliers:
ManufacturerRemarks
X222X
Link not Found
Manufacturer Code:0AM53
Tool Number:IAE 1F10169
Tool Name:IAE 1F10169 Base, remove/install