TASK 05-10-01-200-001-D00 Group A Parts Lives (V2533-A5)

DMC:V2500-A5-05-10-0100-02A-288A-D|Issue No:002.00|Issue Date:2017-05-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

V2500-A5

Description

  1. TASK 05-10-01-200-001-D00 Group A Parts Lives (V2533-A5)

    1. General

      CAUTION

      THE FOLLOWING AIRWORTHINESS LIMITATIONS HAVE BEEN SUBSTANTIATED BASED ON ENGINEERING ANALYSIS THAT ASSUMES THIS PRODUCT WILL BE OPERATED AND MAINTAINED USING THE PROCEDURES AND INSPECTIONS PROVIDED IN THE INSTRUCTIONS FOR CONTINUED AIRWORTHINESS SUPPLIED WITH THIS PRODUCT BY THE TYPE CERTIFICATE HOLDER, OR ITS LICENSEES. FOR ENGINE CRITICAL PARTS AND PARTS THAT INFLUENCE ENGINE CRITICAL PARTS, ANY REPAIR, MODIFICATION OR MAINTENANCE PROCEDURES NOT APPROVED BY THE TYPE CERTIFICATE HOLDER, OR ITS LICENSEES, OR ANY SUBSTITUTION OF SUCH PARTS NOT SUPPLIED BY THE TYPE CERTIFICATE HOLDER, OR ITS LICENSEES, MAY MATERIALLY AFFECT THESE LIMITS. IN SUCH CIRCUMSTANCES, APPROPRIATE AIRWORTHINESS LIMITATION SHOULD BE OBTAINED FROM THE APPLICANT RESPONSIBLE FOR THE REPAIR, MODIFICATION OR SUBSTITUTE PARTS.

      1. The information below is not intended as authority for interchangeability. Refer to the applicable Service Bulletins for interchangeability information.

      2. For definition of an Engine Cycle refer to Chapter/Section 05-10-00 of this manual.

    2. Group A Parts Lives

      LOW PRESSURE COMPRESSOR (LPC) - GROUP A PART LIVES:

      APPROVED LIFE (FLIGHT CYCLES)

      5A0338 - LPC Stage 1 Fan Disk

      (72-31-12, 01-310)

      (Part of 5A0337 - LPC Stage 1 Fan Disk Assembly (72-31-12, 01-200))

      20,000

      5A1758 - LPC Stage 1 Fan Disk (SBE 70-0712)

      (72-31-12, 01-310)

      (Part of 5A1757 - LPC Stage 1 Fan Disk Assembly (72-31-12, 01-200))

      20,000

      5A1949 - LPC Stage 1 Fan Disk (SBE 70-1001)

      (72-31-12, 01-310)

      (Part of 5A1948 - LPC Stage 1 Fan Disk Assembly (72-31-12, 01-200))

      20,000

      5A0896 - Stub Shaft

      (72-32-51, 01-400)

      (Part of 5A0895 - Stub Shaft Assembly (72-32-51, 01-350))

      20,000

      5R0161 - LPC Stage 1.5 To 2.5 Disk

      (72-32-81,02-205)

      (Part of 5R0159 - LPC Stage 1.5 To 2.5 Disk Assembly (72-32-81,02-200))

      20,000

      HIGH PRESSURE COMPRESSOR (HPC) - GROUP A PART LIVES:

      APPROVED LIFE (FLIGHT CYCLES)

      6A6474 - HPC Stage 3 To 8 Disk

      (72-41-11, 01-245)

      (Part of 6A6473, 6A7385 (SBE 72-0304), 6B1380 (SBE 72-0606) - HPC Stage 3 To 8 Disk Assembly (72-41-11, 01-200))

      NOTE

      Do not start at zero flight cycles when the HPC Stage 3 To 8 Disk has been reworked to SBE 72-0304 and SBE 72-0606. Continue to add to existing flight cycles.

      NOTE

      This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, then moved to an A5 or D5, the certified life becomes 15,000 cycles.

      16,000

      6A7402 - HPC Stage 3 To 8 Disk (SBE 72-0300)

      (72-41-11-01-245)

      (Part of 6A7401 (SBE 72-0300), 6B1384 (SBE 72-0606) - HPC Stage 3 To 8 Disk Assembly (72-41-11, 01-200))

      NOTE

      Do not start at zero flight cycles when the HPC Stage 3 To 8 Disk has been reworked to SBE 72-0606. Continue to add to existing flight cycles.

      NOTE

      This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, then moved to an A5 or D5, the certified life becomes 15,000 cycles.

      16,000

      6A7706 - HPC Stage 3 To 8 Disk (SBE 72-0376)

      (72-41-11-01-245)

      (Part of 6A7705 (SBE 72-0376), 6B1385 (SBE 72-0606) - HPC Stage 3 To 8 Disk Assembly (72-41-11, 01-200))

      NOTE

      Do not start at zero flight cycles when the HPC Stage 3 To 8 Disk has been reworked to SBE 72-0606. Continue to add to existing flight cycles.

      NOTE

      This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, then moved to an A5 or D5, the certified life becomes 15,000 cycles.

      20,000

      6A8317 - HPC Stage 3 To 8 Disk (SBE 72-0470)

      (72-41-11-01-245)

      (Part of 6A8316 (SBE 72-0470), 6B1386, 6B1404 (SBE 72-0606) - HPC Stage 3 To 8 Disk Assembly (72-41-11, 01-200))

      NOTE

      Do not start at zero flight cycles when the HPC Stage 3 To 8 Disk has been reworked to SBE 72-0606. Continue to add to existing flight cycles.

      NOTE

      This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, then moved to an A5 or D5, the certified life becomes 15,000 cycles.

      20,000

      6A4156 - HPC Stage 9 To 12 Disk Assembly

      (72-41-12, 01-600)

      8,000

      (Engines Prior To V10253)

      (V10198) - 6A4156 S/N RDN62244

      8,000

      (V10199) - 6A4156 S/N RDN62349

      8,000

      (V10204) - 6A4156 S/N RDN62354

      8,000

      (V10212) - 6A4156 S/N RDN62580

      8,000

      (V10213) - 6A4156 S/N RDN62584

      8,000

      (V10220) - 6A4156 S/N RDN62853

      8,000

      (V10221) - 6A4156 S/N RDN61676

      8,000

      (V10224) - 6A4156 S/N RDN62895

      8,000

      (V10225) - 6A4156 S/N RDN62890

      8,000

      (V10228) - 6A4156 S/N RDN62894

      8,000

      (V10229) - 6A4156 S/N RDN62899

      8,000

      (V10239) - 6A4156 S/N RDN63022

      8,000

      (V10251) - 6A4156 S/N RDN63090

      8,000

      (V10252) - 6A4156 S/N RDN63027

      8,000

      NOTE

      This part is certified for A5 and D5 engine models, however the certified life is different across models and the lowest certified life applies in which the part was operated in. See engine models and part cyclic life below.

      V2522-A5/V2524-A5/V2527-A5/V2527M-A5

      14,300 cycles

      V2527E-A5/V2530-A5

      11,800 cycles

      V2533-A5

      8,000 cycles

      V2525-D5

      15,700 cycles

      V2528-D5

      11,800 cycles

      If there is no record of engine model or models then the part life is 8000 cycles.

      6A6546 - HPC Stage 9 To 12 Disk Assembly (SBE 72-0273)

      (72-41-12, 01-600)

      20,000

      6A7546 - HPC Stage 9 To 12 Disk Assembly (SBE 72-0347)

      (72-41-12, 01-600)

      20,000

      6A7547 - HPC Stage 9 To 12 Disk Assembly (SBE 72-0347)

      (72-41-12, 01-600)

      8,000

      NOTE

      This part is certified for A5 and D5 engine models, however the certified life is different across models and the lowest certified life applies in which the part was operated in. See engine models and part cyclic life below.

      V2522-A5/V2524-A5/V2527-A5/V2527M-A5

      14,300 cycles

      V2527E-A5/V2530-A5

      11,800 cycles

      V2533-A5

      8,000 cycles

      V2525-D5

      15,700 cycles

      V2528-D5

      11,800 cycles

      If there is no record of engine model or models then the part life is 8000 cycles.

      6A5868 - HPC Rear Shaft

      (72-41-13, 01-900)

      (Part of 6A5867 - HPC Rear Shaft Assembly (72-41-13, 01-850))

      20,000

      6A7712 - HPC Rear Shaft (SBE 72-0403)

      (72-41-13, 01-900)

      (Part of 6A7711, 6B1419 (SBE 72-0614) - HPC Rear Shaft Assembly (72-41-13, 01-850))

      20,000

      6A5869 - HPC Rear Rotating Seal (SBE 72-0202)

      (72-41-14, 01-800)

      20,000

      HIGH PRESSURE TURBINE (HPT) - GROUP A PART LIVES:

      APPROVED LIFE (FLIGHT CYCLES)

      2A2801 - HPT Stage 1 Hub

      (72-45-11, 01-011)

      15,000

      2A5001 - HPT Stage 1 Hub (SBE 72-0327)

      (72-45-11, 01-011)

      20,000

      2A1350 - HPT Stage 1 Rotating Outer Air Seal

      (72-45-12, 01-040)

      15,000

      2A3423 - HPT Stage 1 Rotating Outer Air Seal (SBE 72-0327)

      (72-45-12, 01-040)

      20,000

      2A3086 - HPT Stage 1 Rotating Inner Air Seal

      (72-45-13, 01-020)

      15,000

      2A3424 - HPT Stage 1 Rotating Inner Air Seal ( SBE 72-0327)

      (72-45-13, 01-020)

      20,000

      2A3923 - HPT Stage 1 Rotating Inner Air Seal ( SBE 72-0511)

      (72-45-13, 01-020)

      20,000

      2A3179 - HPT Stage 2 Rotating Air Seal

      (72-45-00, 01-080)

      15,000

      2A3425 - HPT Stage 2 Rotating Air Seal (SBE 72-0327)

      (72-45-00, 01-080)

      20,000

      2A3596 - HPT Stage 2 Rotating Air Seal (SBE 72-0412)

      (72-45-00, 01-080)

      20,000

      2A4157 - HPT Stage 2 Rotating Air Seal (SBE 72-0534)

      (72-45-00, 01-080)

      20,000

      2A3002 - HPT Stage 2 Hub

      (72-45-31, 01-011)

      15,000

      2A4802 - HPT Stage 2 Hub (SBE 72-0327)

      (72-45-31, 01-011)

      20,000

      2A2097 - HPT Stage 2 Blade Retaining Plate

      (72-45-33, 01-020)

      15,000

      2A3426 - HPT Stage 2 Blade Retaining Plate (SBE 72-0327)

      (72-45-33, 01-020)

      15,000

      2A3437 - HPT Stage 2 Blade Retaining Plate (SBE 72-0328)

      (72-45-33, 01-020)

      20,000

      LOW PRESSURE TURBINE (LPT) - GROUP A PART LIVES:

      APPROVED LIFE (FLIGHT CYCLES)

      3A2428 - LPT Stage 3 Disk

      (72-50-31, 01-200)

      NOTE

      This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life becomes 10,000 cycles.

      20,000

      3A2508 - LPT Stage 3 Disk (SBE 72-0307)

      (72-50-31, 01-200)

      NOTE

      This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life becomes 10,000 cycles.

      20,000

      3A2513 - LPT Stage 3 Disk (SBE 70-0705)

      (72-50-31, 01-200)

      NOTE

      This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life becomes 10,000 cycles.

      20,000

      3A1984 - LPT Stage 4 Disk

      (72-50-31, 01-150)

      NOTE

      This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life becomes 10,000 cycles.

      20,000

      3A2430 - LPT Stage 5 Disk

      (72-50-31, 01-100)

      20,000

      3A1986 - LPT Stage 6 Disk

      (72-50-31, 01-050)

      20,000

      3A2996 - LPT Stage 6 Disk (SBE 70-0942)

      (72-50-31, 01-050)

      20,000

      3A2424 - LPT Stage 7 Disk

      20,000

      3A2512 - LPT Stage 7 Disk (SBE 72-0307)

      NOTE

      This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 1,001 to 3,000 cycles, then moved to an A5 or D5, the certified life is 19,800, If this part has operated in an A1, bumped for 3,001 to 6,000 cycles, then moved to an A5 or D5, the certified life is 18,500. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life is 10,000.

      20,000

      3A2514 - LPT Stage 7 Disk (SBE 70-0705)

      NOTE

      This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 1,001 to 3,000 cycles, then moved to an A5 or D5, the certified life is 19,800. 1f this part has operated in an A1, bumped for 3,001 to 6,000 cycles, then moved to an A5 or D5, the certified life is 18,500. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life is 10,000.

      20,000

      3A0963 - LPT Stage 3 Rotating Air Seal

      (72-50-33, 01-200)

      20,000

      3A2422 - LPT Stage 4 Rotating Air Seal

      (72-50-33, 01-150)

      20,000

      3A2423 - LPT Stage 5 Rotating Air Seal

      (72-50-33, 01-100)

      20,000

      3A0078 - LPT Stage 6 Rotating Inner Air Seal

      (72-50-00, 01-240)

      20,000

      3A3063 - LPT Stage 6 Rotating Inner Air Seal (SBE 72-0567)

      (72-50-00, 01-240)

      20,000

      3A3047 - LPT Stage 6 Rotating Inner Air Seal (SBE 72-0626)

      (72-50-00, 01-240)

      20,000

      3A1988 - LPT Stage 6 Rotating Air Seal

      (72-50-33, 01-050)

      20,000

      3A1741 - LPT Stage 7 Rotating Air Seal

      (72-50-33, 01-010)

      20,000

      3A2522 - LPT Stage 7 Rotating Air Seal (SBE 70-0707)

      (72-50-33, 01-010)

      20,000

      5A1732 - LPT Shaft

      (72-50-41, 01-200)

      20,000

      5A1762 - LPT Shaft (SBE 70-0605)

      (72-50-41, 01-200)

      20,000

Change Type:

Revised the table to add notes. (15VA010)

Change Type:

Revised the cycle time limits. (15VA010A)