Export Control
EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.Copyright
© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).Applicability
V2500-A5
Description
TASK 05-10-01-200-001-G00 Group A Parts Lives - V2533-A5 (SQ) (SBE 72-0565 - SelectOne Retrofit Standard, SBE 72-0560, SBE 72-0561, SBE 72-0562, SBE 72-0563, SBE 72-0564, and SBE 73-0203 - SelectOne Production Standard)
General
CAUTION
THE FOLLOWING AIRWORTHINESS LIMITATIONS HAVE BEEN SUBSTANTIATED BASED ON ENGINEERING ANALYSIS THAT ASSUMES THIS PRODUCT WILL BE OPERATED AND MAINTAINED USING THE PROCEDURES AND INSPECTIONS PROVIDED IN THE INSTRUCTIONS FOR CONTINUED AIRWORTHINESS SUPPLIED WITH THIS PRODUCT BY THE TYPE CERTIFICATE HOLDER, OR ITS LICENSEES. FOR ENGINE CRITICAL PARTS AND PARTS THAT INFLUENCE ENGINE CRITICAL PARTS, ANY REPAIR, MODIFICATION OR MAINTENANCE PROCEDURES NOT APPROVED BY THE TYPE CERTIFICATE HOLDER, OR ITS LICENSEES, OR ANY SUBSTITUTION OF SUCH PARTS NOT SUPPLIED BY THE TYPE CERTIFICATE HOLDER, OR ITS LICENSEES, MAY MATERIALLY AFFECT THESE LIMITS. IN SUCH CIRCUMSTANCES, APPROPRIATE AIRWORTHINESS LIMITATION SHOULD BE OBTAINED FROM THE APPLICANT RESPONSIBLE FOR THE REPAIR, MODIFICATION OR SUBSTITUTE PARTS.This task lists the Group A Parts and their approved life limits, which are applicable to V2533-A5 (SQ) SelectOne Retrofit Standard engines (SBE 72-0565) and V2533-A5 (SQ) SelectOne Production Standard engines (SBE 72-0560, SBE 72-0561, SBE 72-0562, SBE 72-0563, SBE 72-0564 and SBE 73-0203) only.
The approved Group A Part Lives listed in this task show the approved cyclic lives with and without Consolidated Bump Rating (CBR). Bump usage must be recorded on every individual usage. For further clarification refer to TASK 05-10-00-990-000-B00.
The information below is not intended as authority for interchangeability. Refer to the applicable Service Bulletins for interchangeability information.
For definition of an Engine Cycle refer to Chapter/Section 05-10-00 of this manual.
Group A Part Lives
LOW PRESSURE COMPRESSOR (LPC) - GROUP A PART LIVES:
APPROVED LIFE (FLIGHT CYCLES)
5A0338 - LPC Stage 1 Fan Disk
(72-31-12,01-310)
Bump usage cycles (up to one percent)
(Part of 5A0337 - LPC Stage 1 Fan Disk Assembly (72-31-12,01-200))
20,000
-
0 to 200
5A1758 - LPC Stage 1 Fan Disk (SBE 70-0712)
(72-31-12,01-310)
Bump usage cycles (up to one percent)
(Part of 5A1757 - LPC Stage 1 Fan Disk Assembly (72-31-12,01-200))
20,000
-
0 to 200
5A1949 - LPC Stage 1 Fan Disk (SBE 70-1001)
(72-31-12,01-310)
Bump usage cycles (up to one percent)
(Part of 5A1948 - LPC Stage 1 Fan Disk Assembly (72-31-12,01-200))
20,000
-
0 to 200
5A0896 - Stub Shaft
(72-32-51,01-400)
Bump usage cycles (up to one percent)
(Part of 5A0895 - Stub Shaft Assembly (72-32-51,01-350))
20,000
-
0 to 200
5R0161 - LPC Stage 1.5 To 2.5 Disk
(72-32-81,02-205)
Bump usage cycles (up to one percent)
(Part of 5R0159 - LPC Stage 1.5 To 2.5 Disk Assembly (72-32-81,02-200))
20,000
-
0 to 200
HIGH PRESSURE COMPRESSOR (HPC) - GROUP A PART LIVES:
APPROVED LIFE (FLIGHT CYCLES)
6A7402 - HPC Stage 3 To 8 Disk (SBE 72-0300)
(72-41-11-01-245)
CAUTION
IF PART NUMBER 6A7402 IS INSTALLED, YOU MUST NOT USE BUMP TAKE-OFF RATING.(Part of 6A7401 (SBE 72-0300), 6B1384 (SBE 72-0606), 6B1391 (SBE 72-0605) HPC Stage 3 To 8 Disk Assembly (72-41-11,01-200))
NOTE
Do not start at zero flight cycles when the HPC Stage 3 To 8 Disk has been reworked to SBE 72-0605 or SBE 72-0606. Continue to add to existing flight cycles.NOTE
This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, then moved to an A5 or D5, the certified life becomes 15,000 cycles.16,000
6A7706 - HPC Stage 3 To 8 Disk (SBE 72-0376)
(72-41-11-01-245)
Bump usage cycles (up to one percent)
(Part of 6A7705 (SBE 72-0376), 6B1385 (SBE 72-0606), 6B1392 (SBE 72-605) HPC Stage 3 To 8 Disk Assembly (72-41-11,01-200))
NOTE
Do not start at zero flight cycles when the HPC Stage 3 To 8 Disk has been reworked to SBE 72-0605 or SBE 72-0606. Continue to add to existing flight cycles.NOTE
This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, then moved to an A5 or D5, the certified life becomes 15,000 cycles.20,000
-
0 to 200
6A8317 - HPC Stage 3 To 8 Disk (SBE 72-0470)
(72-41-11-01-245)
Bump usage cycles (up to one percent)
(Part of 6A8316 (SBE 72-0470), 6B1386, 6B1404 (SBE 72-0606), 6B1393, 6B1405 (SBE 72-0605) HPC Stage 3 To 8 Disk Assembly (72-41-11,01-200))
NOTE
Do not start at zero flight cycles when the HPC Stage 3 To 8 Disk has been reworked to SBE 72-0605 or SBE 72-0606. Continue to add to existing flight cycles.NOTE
This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, then moved to an A5 or D5, the certified life becomes 15,000 cycles.20,000
-
0 to 200
6A7546 - HPC Stage 9 To 12 Disk Assembly (SBE 72-0347)
(72-41-12,01-600)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
6A5868 - HPC Rear Shaft (SBE 72-0202)
(72-41-13,01-900)
Bump usage cycles (up to one percent)
(Part of 6A5867 - HPC Rear Shaft Assembly (72-41-13,01-850))
20,000
-
0 to 200
6A7712 - HPC Rear Shaft (SBE 72-0403)
(72-41-13,01-900)
Bump usage cycles (up to one percent)
(Part of 6A7711, 6B1419 (SBE 72-0614) - HPC Rear Shaft Assembly (72-41-13,01-850))
(For engines incorporating SBE 72-0202.
20,000
-
0 to 200
6A5869 - HPC Rear Rotating Seal (SBE 72-0202)
(72-41-14,01-800)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
HIGH PRESSURE TURBINE (HPT) - GROUP A PART LIVES:
APPROVED LIFE (FLIGHT CYCLES)
2A2801 - HPT Stage 1 Hub (SBE 72-0238)
(72-45-11,01-011)
Bump usage cycles (up to one percent)
(Part of 2A3301 - HPT Stage 1 Rotor Assembly (72-45-10,01-010))
15,000
-
0 to 150
2A5001 - HPT Stage 1 Hub (SBE 72-0327)
(72-45-11,01-011)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
2A1350 - HPT Stage 1 Rotating Outer Air Seal
(72-45-12,01-040)
Bump usage cycles (up to one percent)
15,000
-
0 to 150
2A3423 - HPT Stage 1 Rotating Outer Air Seal (SBE 72-0327)
(72-45-12,01-040)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
2A3923 - HPT Stage 1 Rotating Inner Air Seal ( SBE 72-0511)
(72-45-13,01-020)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
2A4157 - HPT Stage 2 Rotating Air Seal (SBE 72-0534)
(72-45-00,01-080)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
2A3002 - HPT Stage 2 Hub (SBE 72-0145)
(72-45-31,01-011)
Bump usage cycles (up to one percent)
(Part of 2A2822 HPT Stage 2 Rotor Assembly (72-45-30,01-010))
15,000
-
0 to 150
2A4802 - HPT Stage 2 Hub (SBE 72-0327)
(72-45-31,01-011)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
2A3426 - HPT Stage 2 Blade Retaining Plate (SBE 72-0327)
(72-45-33,01-020)
Bump usage cycles (up to one percent)
15,000
-
0 to 150
2A3437 - HPT Stage 2 Blade Retaining Plate (SBE 72-0328)
(72-45-33,01-020)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
LOW PRESSURE TURBINE (LPT) - GROUP A PART LIVES:
APPROVED LIFE (FLIGHT CYCLES)
3A2428 - LPT Stage 3 Disk (SBE 70-0522)
(72-50-31,01-200)
Bump usage cycles (up to one percent)
NOTE
This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life becomes 10,000 cycles.20,000
-
0 to 200
3A2508 - LPT Stage 3 Disk (SBE 72-0307)
(72-50-31,01-200)
Bump usage cycles (up to one percent)
NOTE
This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life becomes 10,000 cycles.20,000
-
0 to 200
3A2513 - LPT Stage 3 Disk (SBE 70-0705)
(72-50-31,01-200)
Bump usage cycles (up to one percent)
NOTE
This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life becomes 10,000 cycles.20,000
-
0 to 200
3A1984 - LPT Stage 4 Disk
(72-50-31,01-150)
Bump usage cycles (up to one percent)
NOTE
This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life becomes 10,000 cycles.20,000
-
0 to 200
3A2430 - LPT Stage 5 Disk (SBE 70-0522)
(72-50-31,01-100)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A1986 - LPT Stage 6 Disk
(72-50-31,01-050)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A2996 - LPT Stage 6 Disk (SBE 70-0942)
(72-50-31,01-050)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A2424 - LPT Stage 7 Disk
(72-50-31, 01-010
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A2512 - LPT Stage 7 Disk (SBE 72-0307)
(72-50-31, 01-010)
Bump usage cycles (up to one percent)
NOTE
This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 1,001 to 3,000 cycles, then moved to an A5 or D5, the certified life is 19,800. If this part has operated in an A1, bumped for 3,001 to 6,000 cycles, then moved to an A5 or D5, the certified life is 18,500. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life is 10,000.20,000
-
0 to 200
3A2514 - LPT Stage 7 Disk (SBE 70-0705)
(72-50-31, 01-010)
Bump usage cycles (up to one percent)
NOTE
This part is certified for the A1, A5 and D5, however the certified life is different across models. If this part has operated in an A1, bumped for 1,001 to 3,000 cycles, then moved to an A5 or D5, the certified life is 19,800. If this part has operated in an A1, bumped for 3,001 to 6,000 cycles, then moved to an A5 or D5, the certified life is 18,500. If this part has operated in an A1, bumped for 6,001 or more cycles, then moved to an A5 or D5, the certified life is 10,000.20,000
-
0 to 200
3A0963 - LPT Stage 3 Rotating Air Seal
(72-50-33,01-200)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A2422 - LPT Stage 4 Rotating Air Seal
(72-50-33,01-150)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A2423 - LPT Stage 5 Rotating Air Seal
(72-50-33,01-100)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A0078 - LPT Stage 6 Rotating Inner Air Seal
(72-50-00,01-240)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A3063 - LPT Stage 6 Rotating Inner Air Seal (SBE 72-0567)
(72-50-00,01-240)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A3047 - LPT Stage 6 Rotating Inner Air Seal (SBE 72-0626)
(72-50-00,01-240)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A1988 - LPT Stage 6 Rotating Air Seal
(72-50-33,01-050)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A1741 - LPT Stage 7 Rotating Air Seal
(72-50-33,01-010)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
3A2522 - LPT Stage 7 Rotating Air Seal (SBE 70-0707)
(72-50-33,01-010)
Bump usage cycles (up to one percent)
20,000
-
0 to 200
5A1762 - LPT Shaft (SBE 70-0605)
(72-50-41,01-200)
Bump usage cycles (up to one percent)
20,000
-
0 to 200