TASK 71-00-02-000-019 (A1/A5-PPBU) - Remove The Hydraulic Pump And Filter Assembly, Removal-019

DMC:V2500-A0-71-00-0200-18A-520A-B|Issue No:001.00|Issue Date:2014-05-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 71-00-02-000-019 (A1/A5-PPBU) - Remove The Hydraulic Pump And Filter Assembly, Removal-019

General

Fig./item numbers in parentheses in the procedure agree with those used in the IPC. Only the primary Fig./item numbers are used. For the service bulletin alpha variants refer to the IPC.

For all parts identified in a different Chapter/Section/Subject the applicable Chapter/Section/Subject comes before the Fig/item number.

Apply the approved CoMat 10-058 PENETRATING OIL before the removal of threaded parts. Let the parts soak before removal.

Seal all openings to prevent contamination from unwanted material.

Discard all rubber seal rings removed in this procedure.

NOTE

To identify the consumable materials refer to the PCI.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 10-058 PENETRATING OIL0AM53CoMat 10-058

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 71-00-02-020-050 Remove the Hydraulic Case Drain Filter Assembly

    1. Refer to Figure.

    2. NOTE

      The case drain filter assembly must have its maintenance completed, as given in the Pall Filtrationstechnik Component Maintenance Manual (29-11-43).

      Remove the four bolts that attach the case drain filter to the raft EEC Fan Harness (71-51-41, 05-710). Remove the case drain filter together with the bracket CASE DRAIN HYDRAULIC FILTER ASSEMBLY (29-11-43, 01-900).

    2. SUBTASK 71-00-02-050-021 Remove the Hydraulic Pump

    1. Refer to Figure.

    2. CAUTION

      HOLD THE WEIGHT OF THE HYDRAULIC PUMP DURING THE REMOVAL OF THE NUTS.

      Loosen the four nuts and turn the pump to put the nuts in the large holes.

    3. Remove the hydraulic pump.

    4. Discard the gasket and the seal.

    5. Put the applicable covers/caps/plugs on the gearbox accessory mounting pad.

    3. Figure: Remove the Hydraulic Case Drain Filter Assembly

    Remove the Hydraulic Case Drain Filter Assembly

    Figure: Removal of the Hydraulic Pump

    Removal of the Hydraulic Pump

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:X222X
Supply Number:CoMat 10-058
Type:sp01
Supply Short Name:CoMat 10-058 PENETRATING OIL
Supply Name:CoMat 10-058 PENETRATING OIL
Suppliers:
ManufacturerRemarks
X222X