TASK 71-52-45-300-004 Exhaust Gas Temperature (EGT) Harness - Replace The Sleeve Markers And Sleeve, Repair-004 (VRS1092)

DMC:V2500-A0-71-52-4500-05A-920A-C|Issue No:001.00|Issue Date:2014-05-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 71-52-45-300-004 Exhaust Gas Temperature (EGT) Harness - Replace The Sleeve Markers And Sleeve, Repair-004 (VRS1092)

Effectivity

FIG/ITEM

PART NO.

01-005

2A1490

01-005

6A5878

01-005

6A4720

General

Price and availability - none

The practices and processes referred to in the procedure by the TASK number are in the SPM.

For the method to clean the parts, refer to Cleaning-001 TASK 71-52-45-100-301.

Repair Parts

FIG/ITEM

PART NO.

PART IDENT

QTY

03-722

2A1422

I/band

03-776

RT4116 (1/2 inch)

Tube, heat shrinkable

03-778

RT4116 (3/4 inch)

Tube, heat shrinkable

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NameManufacturerPart Number / IdentificationQuantityRemark
Hot Air GunLOCALHot Air Gun
Hot - markerLOCALHot - marker

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 02-197 COLOR FOILIAE81CoMat 02-197

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 71-52-45-350-059 Remove the Damaged Sleeve Marker and Sleeve

      1. CAUTION

        DO NOT CUT THE CABLE.

        Remove the damaged sleeve marker and sleeve.

      1. Use a knife.

    2. SUBTASK 71-52-45-350-060 Install the Connector and Terminal Identification Marker for the Cable Identification

    1. Refer to Figure.

      2. Trim the heat shrinkable tube and write the identification code.

      1. Use a Hot - marker. Write the connector code for connector and/or terminal.

    3. Install the heat shrinkable tube on the cable.

      4. Heat the heat shrinkable tube

      2. Set to deliver air between 480 and 570 deg F (250 and 300 deg C).

    3. SUBTASK 71-52-45-350-061 Install the New Harness Assembly Identification Sleeve for the Cable Identification

    1. Refer to Figure.

      2. Write the identification code

      1. Use a die or suitable engraving tool. Write the harness assembly Part No. and Serial No. for identification.

      3. Install the I/band

      1. Use a pincer to install the sleeve within approximately 2 in. (50 mm) of connector 400VC ensuring adequate clearance with adjacent clipping points (C5553).

    4. Figure: Replacement of the Sleeve Marker

    Replacement of the Sleeve Marker

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:IAE81
Enterprise Name:CTK CORPORATION
BU Name:CTK CORPORATION
Department:CHO CHIYODA-KU
Street:1-7-17 KANDAWAIZUMI-
City:TOKYO 101
Country:JAPAN
Phone Number:81-3-38615610
Fax Number:81-3-38615880
Manufacturer Code:LOCAL
Enterprise Name:LOCALLY SUPPLIED
Manufacturer Code:IAE81
Supply Number:CoMat 02-197
Type:sp01
Supply Short Name:CoMat 02-197 COLOR FOIL
Supply Name:CoMat 02-197 COLOR FOIL
Specification Groups:
Doc NumberType
T221-10 JCR-262
Suppliers:
ManufacturerRemarks
IAE81
Manufacturer Code:LOCAL
Tool Number:Hot - marker
Tool Name:Hot - marker
Manufacturer Code:LOCAL
Tool Number:Hot Air Gun
Tool Name:Hot Air Gun