TASK 71-71-49-300-005 Fuel Drain Tubes - Repair The End Fittings, Repair-005 (VRS2938)

DMC:V2500-A0-71-71-4900-01A-657A-C|Issue No:001.00|Issue Date:2013-11-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 71-71-49-300-005 Fuel Drain Tubes - Repair The End Fittings, Repair-005 (VRS2938)

Effectivity

FIG/ITEM

PART NO.

01-100

740-5276-503

01-100

745-5276-501

01-500

740-5277-503

01-500

740-5277-507

01-500

740-5277-509

01-500

740-5277-505

02-100

740-5279-505

02-100

740-5279-507

02-100

740-5279-509

02-100

745-5279-501

02-100

745-5279-503

02-500

740-5278-503

02-500

740-5278-505

02-500

740-5278-507

02-500

740-5278-509

02-500

740-5278-511

Material of component

DESCRIPTION

IAE SYMBOL

MATERIAL

Fuel drain tube

Stainless steel

General

This repair can be done on the end fittings of the tube during overhaul.

The practices and processes referred to in the procedure by the TASK numbers are in the SPM.

NOTE

To identify the consumable materials refer to the Overhaul Processes and Consumables Index (PCI).

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NameManufacturerPart Number / IdentificationQuantityRemark
Smooth flat fileLOCALSmooth flat file
Thread tapLOCALThread tap

0.5000-20 UNJF-3B

Thread gageLOCALThread gage

(A GO - NO GO gage to test the size of thread on the thread tap listed above)

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 01-002 SOLVENT, DELETED.0AM53CoMat 01-002
CoMat 02-099 LINT-FREE CLOTHLOCALCoMat 02-099
CoMat 02-102 BRUSH, PAINTLOCALCoMat 02-102
CoMat 10-035 COMPOUND, METAL CUTTING,WATER-TYPE0AM53CoMat 10-035

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 71-71-49-110-052 Clean the End Fittings

      1. Clean the end fittings.

      1. Refer to Cleaning-000 TASK 71-71-49-100-100.

    2. SUBTASK 71-71-49-350-053 Repair the Screw Threads

      CAUTION

      DO NOT DAMAGE THE SEALING FACES OF THE END FITTINGS. IT CAN MAKE THE TUBE UNSERVICEABLE.

      1. Visually examine the screw threads.

      1. If more than three turns of the screw threads are damaged, then discard the end fitting.

      2. Repair the screw threads.

      2. If the Thread tap does not turn easily, discard the end fitting.

      3. Make sure that the dimensions of the screw threads are correct.

      1. Use the Thread gage to measure the size of the threads.

      2. The GO end of the gage must go in the end fitting. The NO-GO end of the gage must not go in the end fitting. If the NO-GO end goes in, discard the end fitting.

    3. SUBTASK 71-71-49-350-054 Repair the Wrench Flats

      1. Make the wrench flats flat and smooth.

      1. Use the Smooth flat file to remove all burrs and scratches.

      2. Measure the distance across the flats at each of three positions.

      1. The distance must be between 0.687 in. (17.45 mm) and 0.683 in. (17.35 mm).

      2. Each pair of flats must be parallel to each other. If the distance is not correct or the flats are not parallel, discard the end fitting.

      3. Clean the end fitting.

      1. Do again Step

    4. SUBTASK 71-71-49-220-057 Examine the End Fitting

      1. Visually examine the end fitting.

      1. Refer to Inspection-000 TASK 71-71-49-200-100.

    5. SUBTASK 71-71-49-230-053 Examine the End Fitting

      1. Do a dye-penetrant test on the end fitting.

      1. Refer to SPM TASK 70-23-05-230-501.

    6. SUBTASK 71-71-49-780-059 Pressure Test the Tube

      1. Do a pressure test on the tube.

      1. Refer to Testing-001 TASK 71-71-49-700-101.

    7. SUBTASK 71-71-49-850-051 Put the Repair Scheme Number on the Tube

      1. Mark the repair scheme number VRS2938 on the tube adjacent to the part number with the electro-etch method.

      1. Refer to SPM TASK 70-09-00-400-501.

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:LOCAL
Enterprise Name:LOCALLY SUPPLIED
Manufacturer Code:X111X
Supply Number:CoMat 01-002
Type:sp01
Supply Short Name:CoMat 01-002 SOLVENT, DELETED.
Supply Name:CoMat 01-002 SOLVENT, DELETED.
Specification Groups:
Doc NumberType
wiring harnesses. Where CoMat 01‐002 is specified to clean mechanical components, use one or more of the solvents that SPM TASK 70‐11‐26‐300‐503 specifies as applicable.DELETED. Where CoMat 01‐002 is specified to clean electrical contacts or wiring harnesses, use one or more of the solvents that SPM TASK 70‐11‐57‐110‐501 specifies to clean electrical contacts or
Suppliers:
ManufacturerRemarks
X111X
Manufacturer Code:X222X
Supply Number:CoMat 02-099
Type:sp01
Supply Short Name:CoMat 02-099 LINT-FREE CLOTH
Supply Name:CoMat 02-099 LINT-FREE CLOTH
Specification Groups:
Doc NumberType
WHERE COMAT 02-099 IS SPECIFIED WITH NO SUFFIX, USE COMAT 02-099A OR COMAT 02-099B.
Suppliers:
ManufacturerRemarks
X222X
Manufacturer Code:LOCAL
Supply Number:CoMat 02-102
Type:sp01
Supply Short Name:CoMat 02-102 BRUSH, PAINT
Supply Name:CoMat 02-102 BRUSH, PAINT
Specification Groups:
Doc NumberType
PAINT-BRUSH
Suppliers:
ManufacturerRemarks
LOCAL
Manufacturer Code:0AM53
Supply Number:CoMat 10-035
Type:sp01
Supply Short Name:CoMat 10-035 COMPOUND, METAL CUTTING,WATER-TYPE
Supply Name:CoMat 10-035 COMPOUND, METAL CUTTING,WATER-TYPE
Specification Groups:
Doc NumberType
DELETED
Suppliers:
ManufacturerRemarks
0AM53
Manufacturer Code:LOCAL
Tool Number:Smooth flat file
Tool Name:Smooth flat file
Manufacturer Code:LOCAL
Tool Number:Thread gage
Tool Name:Thread gage
Manufacturer Code:LOCAL
Tool Number:Thread tap
Tool Name:Thread tap