TASK 72-00-60-300-010 External Gearbox Module - Rear Link - Replace The Spherical Bearing, Repair-010 (VRS5386)

DMC:V2500-A0-72-00-6003-00A-920A-C|Issue No:004.00|Issue Date:2021-08-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-00-60-300-010 External Gearbox Module - Rear Link - Replace The Spherical Bearing, Repair-010 (VRS5386)

Effectivity

FIG/ITEM

PART NO.

01-200

4B0031

Material of component

DESCRIPTION

MATERIAL

Bearing

Corrosion resistant steel

Link

Corrosion resistant steel

General

NOTE

To identify the consumable materials refer to the PCI.

NOTE

Special tools are identified in the procedure by the tool primary number.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NameManufacturerPart Number / IdentificationQuantityRemark
Workshop inspection equipmentLOCALWorkshop inspection equipment
Cutting toolLOCALCutting tool
Arbor PressLOCALArbor press
OvenLOCALOven
Arbor PressLOCALArbor press
IAE 3F10375 Base, remove/install0AM53IAE 3F103751
IAE 3F10376 Drifts, remove/install0AM53IAE 3F103761

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 01-124 ISOPROPYL ALCOHOLLOCALCoMat 01-124
CoMat 02-099 LINT-FREE CLOTHX222XCoMat 02-099
CoMat 06-063 FLUORESCENT PENETRANT (POST-EMULSIFIED MEDIUM SENSITIVITY)X222XCoMat 06-063
CoMat 10-077 APPROVED ENGINE OILSLOCALCoMat 10-077

Spares

NameManufacturerPart Number / IdentificationQuantityRemark
BEARING, SPHERICAL0AM534T0142A/R

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-00-60-350-059 Remove the Bearing

    1. Refer to Figure.

      2. CAUTION

        DO NOT PERMIT THE CUTTING TOOL TO TOUCH THE LINK. THIS WILL CAUSE DAMAGE TO THE LINK.
        REMOVE ALL STAKING LIP PIECES BEFORE YOU PUSH OUT THE BEARING. THESE MIGHT CASE DAMAGE TO THE LINK BORE.

        Install the rear link in the base.

      3. Cut a groove in the outer race of the bearing and remove the staking lip.

      1. Use cutting tool.

      4. Push out the bearing.

      1. Push on the side where the staking lip has been removed.

    2. SUBTASK 72-00-60-220-085 Visually Examine the Rear Link Bearing Bore

    1. Examine the link bore and chamfer.

      2. Remove evident nicks.

      1. Use fine abrasive paper.

      3. Do a penetrant crack test.

      1. Refer to the SPM TASK 70-23-01-230-501.

      3. Examine one bore at a time.

      4. Cracks are not permitted.

    3. SUBTASK 72-00-60-110-065 Clean the Link and the New Bearing

      1. Clean the link and the bearing.

    4. SUBTASK 72-00-60-350-060 Install the New Spherical Bearing

    1. Refer to Figure.

      2. CAUTION

        DO NOT TOUCH THE HOT PARTS WITHOUT PROTECTIVE GLOVES.
        HOT PARTS CAN CAUSE REDDENING AND BLISTERING OF THE SKIN IF THE HANDS ARE NOT PROTECTED.
        IMMERSE THE CONTACTED AREA IN COLD WATER FOR 10 MINUTES IF THE SKIN IS BURNED. IMMEDIATELY GET THE MEDICAL ATTENTION IF PAIN OR BLISTERING PERSISTS.

        Increase the temperature of the link.

      1. Use an oven.

        Increase the temperature of the link to 302 deg F (150 deg C).

      3. CAUTION

        INSTALL THE BEARING IN THE LINK BORE AS SOON AS POSSIBLE OR BEARING CANNOT BE INSTALLED CORRECTLY.

        Remove the link from the oven.

      1. Use protective gloves.

      4. Apply the engine oil.

      1. Use a brush to apply a coat of CoMat 10-077 APPROVED ENGINE OILS to the link bore suface and to the outside surface of the bearing.

      5. Install the link on the base.

      6. Install the bearing on the guide of the base.

      7. CAUTION

        DO NOT PRESS ON THE BALL OF THE BEARING.

        Install the bearing.

      1. Use an arbor press and IAE 3F10376 Drifts, remove/install 1 off to press the bearing in to the link bore.

        Apply a maximum load of 1101.5 lbf (500 kg).

    8. Remove the link and the bearing from the base.

    5. SUBTASK 72-00-60-350-061 Fasten the Bearing to the Link

    1. Refer to Figure.

      2. Install the link on the guide of the base (1st calking).

      3. Initially stake the bearing.

      1. Use IAE 3F10376 Drifts, remove/install 1 off and an arbor press.

        Apply a gradually increasing load until the bearing retention staking lip is bent sufficiently. Load must not be more than 17624 lbf (8000 kg).

      4. Install the link on the guide of the base (2nd calking).

      5. Finally stake the bearing.

      1. Use IAE 3F10376 Drifts, remove/install and an arbor press.

        Apply a gradually increasing load until the retention lip of the bearing race contacts the bore chamfer of the link. Load must not be more than 17624 lbf (8000 kg).

      6. Turn the link and fasten the other side of the bearing.

      1. Do again Step to Step.

    6. SUBTASK 72-00-60-350-062 Examine the Assembled Bearing

    1. Refer to Figure.

      2. Examine the bearing.

      1. Make sure that there is free movement of the bearing within the race.

        Make sure that there is no movement between the outer race and the link.

    7. SUBTASK 72-00-60-350-063 Identify the Repair

    1. Refer to Figure.

      2. Make a mark VRS5386 adjacent to the part number.

      1. Refer to SPM TASK 70-09-00-400-501.

    8. Figure: Repair details and dimensions

    Repair details and dimensions

Requirements After Job Completion

Follow-On Conditions

NONE
Change Type:

Revised the procedural steps. (21VC151)

Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:LOCAL
Enterprise Name:LOCALLY SUPPLIED
Manufacturer Code:X222X
Enterprise Name:N/A – REFER TO APPLICABLE COMAT SUFFIX
Part Number:4T0142
Part Name:BEARING, SPHERICAL
Manufacturer Code:0AM53
Manufacturer Code:LOCAL
Supply Number:CoMat 01-124
Type:sp01
Supply Short Name:CoMat 01-124 ISOPROPYL ALCOHOL
Supply Name:CoMat 01-124 ISOPROPYL ALCOHOL
Specification Groups:
Doc NumberType
OMAT:1/40GPR TECHNICAL GRADE
PMC 9094GPR TECHNICAL GRADE
JCR-011GPR TECHNICAL GRADE
Suppliers:
ManufacturerRemarks
LOCAL
U1185
24853
K6835
Manufacturer Code:X222X
Supply Number:CoMat 02-099
Type:sp01
Supply Short Name:CoMat 02-099 LINT-FREE CLOTH
Supply Name:CoMat 02-099 LINT-FREE CLOTH
Specification Groups:
Doc NumberType
WHERE COMAT 02-099 IS SPECIFIED WITH NO SUFFIX, USE COMAT 02-099A OR COMAT 02-099B.
Suppliers:
ManufacturerRemarks
X222X
Manufacturer Code:X222X
Supply Number:CoMat 06-063
Type:sp01
Supply Short Name:CoMat 06-063 FLUORESCENT PENETRANT (POST-EMULSIFIED MEDIUM SENSITIVITY)
Supply Name:CoMat 06-063 FLUORESCENT PENETRANT (POST-EMULSIFIED MEDIUM SENSITIVITY)
Specification Groups:
Doc NumberType
It is not permitted to mix the selected CoMat 06‐063 letter suffix material with other CoMat 06‐063 letter suffix materials. Where CoMat 06‐063 is specified with no suffix, use one of the CoMat 06‐063 letter suffix materials.
Suppliers:
ManufacturerRemarks
X222X
Manufacturer Code:X333X
Supply Number:CoMat 10-077
Type:sp01
Supply Short Name:CoMat 10-077 APPROVED ENGINE OILS
Supply Name:CoMat 10-077 APPROVED ENGINE OILS
Specification Groups:
Doc NumberType
For V2500-A1/A5/D5 models - Refer to V2500 Service Bulletin ENG-79-0108
For V2500-E5 model - Refer to Service Bulletin E5-79-0001
Suppliers:
ManufacturerRemarks
X333X
Manufacturer Code:LOCAL
Tool Number:Arbor press
Tool Name:Arbor Press
Manufacturer Code:LOCAL
Tool Number:Cutting tool
Tool Name:Cutting tool
Manufacturer Code:0AM53
Tool Number:IAE 3F10375
Tool Name:IAE 3F10375 Base, remove/install
Manufacturer Code:0AM53
Tool Number:IAE 3F10376
Tool Name:IAE 3F10376 Drifts, remove/install
Manufacturer Code:LOCAL
Tool Number:Oven
Tool Name:Oven
Manufacturer Code:LOCAL
Tool Number:Workshop inspection equipment
Tool Name:Workshop inspection equipment