TASK 72-32-60-200-003-A00 LPC Bleed Duct Seal Retainer - Examine, Inspection-003

DMC:V2500-A0-72-32-6003-00A-300A-C|Issue No:003.00|Issue Date:2020-05-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-32-60-200-003-A00 LPC Bleed Duct Seal Retainer - Examine, Inspection-003

Effectivity

FIG/ITEM

PART NO.

01-100

5W2115

01-100

5W2230

General

This TASK procedure for the inspection of the seal retainers. For the other bleed valve outlet case parts, refer to TASK 72-32-60-200-000 (INSPECTION-000).

Fig/item numbers in parentheses in the procedure agree with those used in IPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the IPC.

The policy that is necessary for check is given in the SPM TASK 70-21-01-200-501.

All the parts must be cleaned before any part is examined. Refer to TASK 72-32-60-100-000 (CLEANING-000).

All the parts must be visually examined for damage, corrosion and wear. Any defects that are not identified in the procedure must be referred to IAE.

Do not discard any part until you are sure there are no repairs available. Refer to the instruction in Repair before a discarded part is used again oversize parts are installed.

Parts which should be discarded can be held although no repair is available. The repair of a discarded part could be shown to be necessary at a later date.

All parts must be examined to make sure that all the repairs have been completed satisfactorily.

The practices and processes referred to in the procedure by the TASK number are in the SPM.

References

Refer to the SPM for data on these items.

Definitions of Damage, SPM TASK 70-02-02-350-501.

Inspection of PARTS, SPM TASK 70-21-01-220-501.

Some data on these items are contained in this TASK. For more than data on these items refer to the SPM.

Method of Testing for Crack Indications.

Chemical Processes.

Surface Protection.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

NONE

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-32-60-220-061 Examine the Seal Retainers (01-100) Surface

      1. Examine all the surface.

        1. Scored.

          1. Any scores.

          1. Repair, VRS1351 TASK 72-32-60-300-004 (REPAIR-004).

        2. Nicked.

          1. Any nicks.

          1. Repair, VRS1351 TASK 72-32-60-300-004 (REPAIR-004).

        3. Scratched.

          1. Any scratches.

          1. Repair, VRS1351 TASK 72-32-60-300-004 (REPAIR-004).

        4. Dented.

          1. Any dents.

          1. Repair, VRS1351 TASK 72-32-60-300-004 (REPAIR-004).

        5. Cracked.

          1. Any cracks.

          1. Reject.

Requirements After Job Completion

Follow-On Conditions

NONE
Change Type:

Added steps. (88VJ5420)