TASK 72-60-31-200-002-C00 Deoiler Carbon Seal - Examine, Inspection-002

DMC:V2500-A0-72-60-3106-00C-300A-C|Issue No:001.00|Issue Date:2013-11-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-60-31-200-002-C00 Deoiler Carbon Seal - Examine, Inspection-002

Effectivity

FIG/ITEM

PART NO.

01-150

7T0454

General

This TASK gives the procedure for the inspection of the carbon seal.

Fig/item numbers in parentheses in the procedure with those used in the IPC

The policy that is necessary for inspection is given in the SPM TASK 70-20-00-200-501.

All the parts must be cleaned before any part is examined. Refer to the SPM TASK 70-10-00-100-501.

All parts must be visually examined for damage, corrosion and wear.

Any defects that are not identified in the procedure must be referred to IAE.

Parts which should be discarded can be held although no repair is available. The repair of the discarded part could be available at a later date.

The practices and processes referred to in the procedure by the TASK numbers are in the SPM.

References

Refer to the SPM for data on these items.

Definition of Damage, TASK 70-02-02-350-501

Record and Control of the Lives of the Parts, TASK 70-05-00-220-501

Inspection of Parts, TASK 70-20-00-200-501

Some data on these items is contained in this TASK. For more data on these items refer to the SPM.

Surface protection

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NameManufacturerPart Number / IdentificationQuantityRemark
Workshop inspection equipmentLOCALWorkshop inspection equipment

Consumables, Materials and Expendables

NONE

Spares

NONE

Safety Requirements

CAUTION

HANDLE THE PART CAREFULLY. CARBON DETAIL IS FRAGILE

Procedure

    1. SUBTASK 72-60-31-220-068 Examine the Carbon Seal (01-150) Nose at Location 1

    1. Refer to Figure.

      2. Cracks.

        1. Evident cracks

        1. Reject

      3. Nicks and Scratches.

        1. Not detectable with a 0.015 to 0.020 in. (0.381 to 0.508 mm) radius style

        1. Accept

        2. More than Step

        1. Reject

      4. Chipped edges.

        1. No greater than 25 percent of original sealing surface width and 25 percent of seal face circumference, no longer than 0.20 in. (5.08 mm)

        1. Accept

        2. More than Step

        1. Reject

    2. SUBTASK 72-60-31-220-069 Examine the Carbon Seal (01-150) Face at Location 2

    1. Refer to Figure.

      2. Cracks.

        1. Evident cracks

        1. Reject

      3. Nicks and scratches.

        1. Not detectable with a 0.015 to 0.200 in. (0.381 to 0.508 mm) radius style

        1. Accept

        2. More than Step

        1. Reject

      4. Chipped edges.

        1. No greater than 25 percent of original sealing surface width and 25 percent of seal face circumference, no longer than 0.20 in. (5.08 mm)

        1. Accept

        2. More than Step

        1. Reject

      5. Freedom of Movement.

      1. No sticking of details is permitted

      6. Flatness.

        1. Within 0.000035 in. (0.00088 mm)

        1. Accept

        2. More than 0.000035 in. (0.00088 mm)

        1. Reject

      7. Free length.

        1. Less than 0.709 in. (18.008 mm)

        1. Reject

    3. SUBTASK 72-60-31-220-070 Examine the Carbon Seal (01-150) Outer Diameter at Location 3

    1. Refer to Figure.

      2. Diameter.

        1. Between 2.643 and 2.642 in. (67.132 and 67.107 mm)

        1. Accept

        2. Less than 2.642 in. (67.107 mm)

        1. Reject

    4. Figure: Locations - Carbon Seal

    Locations - Carbon Seal

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:LOCAL
Enterprise Name:LOCALLY SUPPLIED
Manufacturer Code:LOCAL
Tool Number:Workshop inspection equipment
Tool Name:Workshop inspection equipment