TASK 75-24-49-440-101-A00 LPT ACC Air Ducts And Tubes - Assemble The Support Assemblies To The Tubes And Ducts, Assembly-001 - PRE SBE 75-0001

DMC:V2500-A1-75-24-4900-00A-710A-C|Issue No:002.00|Issue Date:2019-11-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 75-24-49-440-101-A00 LPT ACC Air Ducts And Tubes - Assemble The Support Assemblies To The Tubes And Ducts, Assembly-001 - PRE SBE 75-0001

General

Fig/item numbers in parentheses in the procedure agree with those used in the EIPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the EIPC.

For all parts identified in a different Chapter/Section/Subject, the applicable Chapter/Section/Subject comes before the Fig/item number.

For standard torque data and procedures, refer to SPM TASK 70-41-00-400-501 and SPM TASK 70-41-02-400-501.

Special torque data and assembly tolerances are included in the procedure.

WARNING

DO NOT GET ANTI-SEIZE PASTE ON YOUR SKIN WHEN YOU LUBRICATE THREADS AND ABUTMENT FACES OF NUTS AND BOLTS. WEAR PROTECTIVE GLOVES.

Lubricate all threads and abutment faces of nuts and bolts with CoMat 10-129A ANTI-SEIZE PASTE, unless other lubricants are referred to in the procedure.

To identify, lubricate and install seal rings. Refer to SPM TASK 70-44-01-400-501.

After assembly apply CoMat 07-038 AIR DRYING ENAMEL to any damaged surface protection, joint flanges and attach parts. Use the correct color of the CoMat 07-038 AIR DRYING ENAMEL. Refer to SPM TASK 70-63-02-380-501.

The number for each radial location must be identified in a clockwise direction. These start at the engine top position when you look from the rear of the engine, unless stated differently in the procedure.

Refer to Figure for a view of the LP turbine ACC assembly.

NOTE

The support assemblies of PRE SBE 75-0001 and SBE 75-0001 configurations are interchangeable. For SBE 75-0001 configuration, refer to Assembly-001 TASK 75-24-49-440-101-B00.

NOTE

To identify the consumable materials refer to the PCI.

NOTE

Special tools are identified in the procedure by the tool primary number.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NameManufacturerPart Number / IdentificationQuantityRemark
IAE 1M14084 Support fixture0AM53IAE 1M140842

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 07-038 AIR DRYING ENAMELK3504CoMat 07-038
CoMat 10-129A ANTI-SEIZE PASTE71984CoMat 10-129A

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 75-24-49-440-056 Install the Lower LP Turbine Cooling Air Duct to the Support Fixture

    1. Refer to Figure.

    2. Install the lower LP turbine cooling air duct to the IAE 1M14084 Support fixture 1 off. Make sure that the tube ends are engaged correctly in their holes.

    3. Safety the lower LP turbine cooling air duct to the IAE 1M14084 Support fixture with the swing bolt, the knurled knob, the two washers and the two screws.

    2. SUBTASK 75-24-49-440-052 Install the Support Assembly B to the Lower LP Turbine Cooling Air Duct

    1. Refer to Figure and Figure.

    2. NOTE

      For the location of the support assembly, refer to Figure.

      Install the support assembly B and the two half loop clamps to the lower LP turbine cooling air duct.

    3. Attach the half loop clamps with the 20 bolts and nuts to the support assembly B.

    4. Tighten the nuts temporarily.

    3. SUBTASK 75-24-49-440-057 Install the Support Assemblies C and D to the Lower LP Turbine Cooling Air Duct

    1. Refer to Figure and Figure.

    2. NOTE

      For the location of the support assemblies, refer to Figure.

      Install the support assemblies C and D with the half loop clamps to the lower LP turbine cooling air duct.

    3. Attach the half loop clamps with the 20 bolts and nuts to the support assemblies C and D.

    4. Tighten the nuts temporarily.

    4. SUBTASK 75-24-49-440-054 Install the Support Assembly E to the Lower LP Turbine Cooling Air Duct

    1. Refer to Figure and Figure.

    2. NOTE

      For the location of the support assembly, refer to Figure.

      Install the support assembly E and the two half loop clamps to the lower LP turbine cooling air duct.

    3. Attach the half loop clamps with the 20 bolts and nuts to the support assembly E.

    4. Tighten the nuts temporarily.

    5. SUBTASK 75-24-49-440-058 Remove the Lower LP Turbine Cooling Air Duct from the Support Fixture

    1. Refer to Figure.

    2. Loosen the knurled knob and move the swing bolt out. Remove the two screws and the two washers which safety the lower LP turbine cooling air duct to the IAE 1M14084 Support fixture.

    3. Remove the lower LP turbine cooling air duct from the IAE 1M14084 Support fixture.

    6. SUBTASK 75-24-49-440-051 Install the Upper LP Turbine Cooling Air Duct to the Support Fixture

    1. Refer to Figure.

    2. Install the upper LP turbine cooling air duct to the IAE 1M14084 Support fixture 1 off. Make sure that the tube ends are correctly engaged in their holes.

    3. Safety the upper LP turbine cooling air duct to the IAE 1M14084 Support fixture with the swing bolt the two washers and the two screws.

    7. SUBTASK 75-24-49-440-053 Install the Support Assemblies A and F to the Upper LP Turbine Cooling Air Duct

    1. Refer to Figure and Figure.

    2. NOTE

      For the location of the support assemblies, refer to Figure.

      Install the support assemblies A and F and the two half loop clamps to the upper LP turbine cooling air duct.

    3. Attach the half loop clamps with the 20 bolts and nuts to the support assemblies.

    4. Tighten the nuts temporarily.

    8. SUBTASK 75-24-49-440-055 Remove the Upper LP Turbine Cooling Air Duct from the Support Fixture

    1. Refer to Figure.

    2. Loosen the knurled knob and move the swing bolt out. Remove the two screws and the two washers which safety the upper LP turbine cooling air duct to the IAE 1M14084 Support fixture.

    3. Remove the upper LP turbine cooling air duct from the IAE 1M14084 Support fixture.

    9. Figure: Install/Remove the LP Turbine Cooling Air Duct to/from the Support Fixture

    Install/Remove the LP Turbine Cooling Air Duct to/from the Support Fixture

    Figure: Position of the Support Assemblies

    Position of the Support Assemblies

    Figure: Installation of the Support Assemblies to the Upper LP Turbine Cooling Air Duct

    Installation of the Support Assemblies to the Upper LP Turbine Cooling Air Duct

    Figure: Installation of the Support Assemblies to the Lower LP Turbine Cooling Air Duct

    Installation of the Support Assemblies to the Lower LP Turbine Cooling Air Duct

Requirements After Job Completion

Follow-On Conditions

NONE
Change Type:

Revised tool nomenclature. (Editorial)

Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:71984
Enterprise Name:DOW SILICONES CORP
BU Name:DOW SILICONES CORP
Street:2200 W SALZBURG RD
City:MIDLAND
State:MI
Zip Code:48611
Country:UNITED STATES OF AMERICA
Phone Number:1-800-248-2481, 1-989-496-7881, 1-989-496-6000
Fax Number:1-989-496-6731, 1-989-496-5956
Internet:www.dowcorning.com
Manufacturer Code:K3504
Enterprise Name:INDESTRUCTIBLE PAINT CO LTD
BU Name:NULL
Street:25 PENTOS DRIVE
City:SPARKHILL
Province:BIRMINGHAM
Zip Code:B11 3TA
Country:GREAT BRITAIN
Phone Number:44-121-7022485
Fax Number:44-121-7784338
Email:sales@indestructible.co.uk
Internet:www.indestructible.co.uk
Manufacturer Code:00BB6
Supply Number:CoMat 07-038
Type:sp01
Supply Short Name:CoMat 07-038 AIR DRYING ENAMEL
Supply Name:CoMat 07-038 AIR DRYING ENAMEL
Specification Groups:
Doc NumberType
OMAT:7/22B (RR REF)IP9138 R1
JCR-029 (JAEC REF)
Suppliers:
ManufacturerRemarks
00BB6
K3504
Manufacturer Code:3CU95
Supply Number:CoMat 10-129A
Type:sp01
Supply Short Name:CoMat 10-129A ANTI-SEIZE PASTE
Supply Name:CoMat 10-129A ANTI-SEIZE PASTE
Specification Groups:
Doc NumberType
MOLYKOTE P-37
Suppliers:
ManufacturerRemarks
3CU95
818U1
Manufacturer Code:0AM53
Tool Number:IAE 1M14084
Tool Name:IAE 1M14084 Support fixture