TASK 70-11-48-110-501 Make-Up Of Cleaning Solutions

DMC:V2500-00-70-11-48-01A-081A-D|Issue No:009.00|Issue Date:2020-08-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 70-11-48-110-501 Make-Up Of Cleaning Solutions

General

For a cross reference list of IAE solution code numbers to equivalent party company designations, refer to TASK 70-11-58-110-501, SUBTASK 70-11-58-110-001.

Introduction

Safety Precautions

Equipment and Material

Solution Code 1

Solution Code 4

Solution Code 10

Solution Code 14

Solution Code 20

Solution Code 21

Solution Code 22

Solution Code 23

Solution Code 24

Solution Code 26

Solution Code 72

Solution Code 75

Solution Code 78

Solution Code 79

Solution Code 91

Solution Code 92

Solution Code 94

Solution Code 96

Solution Code 97

Solution Code 100

Solution Code 106

Solution Code 108

Solution Code 109

Solution Code 111

Solution Code 113

Solution Code 114

Solution Code 115

Solution Code 117

Solution Code 119

Solution Code 120

Solution Code 123

Solution Code 124

Solution Code 125

Solution Code 126

Solution Code 127

Solution Code 128

Solution Code 130

Solution Code 131

Solution Code 132

Solution Code 133

Solution Code 134

Solution Code 140

Solution Code 142

Solution Code 143

Solution Code 145

Solution Code 149

Solution Code 157

Solution Code 158

Solution Code 160

Solution Code 161

Solution Code 162

Solution Code 168

Solution Code 171

Solution Code 172

Solution Code 173

Solution Code 175

Solution Code 176 - DELETED

Solution Code 178

Solution Code 179

Solution Code 180

Solution Code 181

Solution Code 190

Solution Code 191

Solution Code 192

Solution Code 193

Solution Code 208

Step

Solution Code 209

Step

Introduction

Cleaning solutions are arranged in numerical order for location.

References to these solutions are made in the cleaning SUBTASKS as necessary.

The make-up and subsequent maintenance of operating limits must be carefully controlled for optimum results.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 01-022 SODIUM HYDROXIDE NaOH (SOLID)LOCALCoMat 01-022
CoMat 01-025 NITRIC ACID HNO3, TECHNICAL GRADELOCALCoMat 01-025
CoMat 01-055 POTASSIUM PERMANGANATE KMnO4LOCALCoMat 01-055
CoMat 01-072 PRIMARY CLEANERLOCALCoMat 01-072
CoMat 01-124 ISOPROPYL ALCOHOLLOCALCoMat 01-124
CoMat 01-130A POTASSIUM HYDROXIDE KOH24853CoMat 01-130A
CoMat 01-188 ALKALINE RUST REMOVER (LIQUID)LOCALCoMat 01-188
CoMat 01-202 WET ABRASIVE COMPOUND8B756CoMat 01-202
CoMat 01-204 WET ABRASIVE COMPOUND8B756CoMat 01-204
CoMat 01-207 ANTISOLIDIFYING COMPOUND62755CoMat 01-207
CoMat 01-230C COMPRESSOR WASHING FLUIDLOCALCoMat 01-230C
CoMat 01-230D COMPRESSOR WASHING FLUIDLOCALCoMat 01-230D
CoMat 01-230E COMPRESSOR WASHING FLUIDLOCALCoMat 01-230E
CoMat 01-230F COMPRESSOR WASHING FLUIDLOCALCoMat 01-230F
CoMat 01-230G COMPRESSOR WASHING FLUIDLOCALCoMat 01-230G
CoMat 01-230H COMPRESSOR WASHING FLUIDLOCALCoMat 01-230H
CoMat 01-230J COMPRESSOR WASHING FLUIDLOCALCoMat 01-230J
CoMat 01-230K COMPRESSOR WASHING FLUIDLOCALCoMat 01-230K
CoMat 01-230L COMPRESSOR WASHING FLUIDLOCALCoMat 01-230L
CoMat 01-265 ADDITIVELOCALCoMat 01-265
CoMat 01-300 ALKALI CLEANER (GENERAL PURPOSE)0GA37CoMat 01-300
CoMat 01-327 NITRIC ACIDLOCALCoMat 01-327
CoMat 01-339 ALKALI CLEANER (GENERAL PURPOSE)LOCALCoMat 01-339
CoMat 01-340 ALKALI CLEANER (GENERAL PURPOSE)LOCALCoMat 01-340
CoMat 01-368 ALKALINE RUST REMOVERLOCALCoMat 01-368
CoMat 01-369 ALKALINE RUST REMOVER71410CoMat 01-369
CoMat 01-417 ALKALINE RUST REMOVER (LIQUID)K4754CoMat 01-417
CoMat 01-418 ADDITIVE, ALKALINE RUST REMOVERLOCALCoMat 01-418
CoMat 01-421 CLEANER, ALKALI (GENERAL PURPOSE, LOW FOAM)IAE63CoMat 01-421
CoMat 01-426 ACIDIC SCALE CONDITIONERLOCALCoMat 01-426
CoMat 01-443 ALKALINE PERMANGANATE (LIQUID)LOCALCoMat 01-443
CoMat 01-444 ADDITIVE (CAUSTIC), ALKALINE PERMANGANATELOCALCoMat 01-444
CoMat 01-445 ADDITIVE (PERMANGANATE), ALKALINE PERMANGANATELOCALCoMat 01-445
CoMat 01-446 ACIDIC SCALE CONDITIONER71410CoMat 01-446
CoMat 01-468 AQUEOUS CLEANER (LOW FOAM)LOCALCoMat 01-468
CoMat 01-469 AQUEOUS DEGREASER1EYE7CoMat 01-469
CoMat 01-474 PHOSPHORIC ACID, INHIBITEDLOCALCoMat 01-474
CoMat 01-478 ACIDIC SCALE CONDITIONERLOCALCoMat 01-478
CoMat 01-479 AQUEOUS DEGREASERLOCALCoMat 01-479
CoMat 01-480 AQUEOUS DEGREASERLOCALCoMat 01-480
CoMat 01-481 AQUEOUS DEGREASER63247CoMat 01-481
CoMat 01-483 AQUEOUS DEGREASERLOCALCoMat 01-483
CoMat 01-486 AQUEOUS DEGREASERLOCALCoMat 01-486
CoMat 01-487 AQUEOUS DEGREASER94058CoMat 01-487
CoMat 01-488 AQUEOUS DEGREASER63247CoMat 01-488
CoMat 01-501 CORROSION INHIBITOR (WATER SOLUBLE)LOCALCoMat 01-501
CoMat 01-502 CORROSION INHIBITOR (WATER SOLUBLE)LOCALCoMat 01-502
CoMat 01-503A ALKALINE PERMANGANATE, PART 1LOCALCoMat 01-503A
CoMat 01-503B ALKALINE PERMANGANATE, PART 2LOCALCoMat 01-503B
CoMat 01-509 AQUEOUS DEGREASERZ0142CoMat 01-509
CoMat 01-540 AQUEOUS CLEANER89524CoMat 01-540
CoMat 01-541A ADDITIVE (ALKALINE PERMANGATE)LOCALCoMat 01-541A
CoMat 01-541B ALKALINE PERMANGATE LIQUIDLOCALCoMat 01-541B
CoMat 01-542 ACID SCALE CONDITIONERLOCALCoMat 01-542
CoMat 01-546A ALKALINE PERMANGANATE, LIQUID, CAUSTIC COMPONENTLOCALCoMat 01-546A
CoMat 01-546B ALKALINE PERMANGANATE, LIQUID, PERMANGANATE CONCENTRATE COMPONENTLOCALCoMat 01-546B
CoMat 01-558A ALKALINE PERMANGANATE, LIQUID, CAUSTIC COMPONENTLOCALCoMat 01-558A
CoMat 01-558B ALKALINE PERMANGANATE, LIQUID, PERMANGANATE COMPONENTLOCALCoMat 01-558B
CoMat 01-564 AQUEOUS DEGREASERLOCALCoMat 01-564
CoMat 01-565 AQUEOUS CLEANER0WUA8CoMat 01-565
CoMat 01-571 ALKALINE RUST REMOVERLOCALCoMat 01-571
CoMat 01-572 SODIUM HYDROXIDE NaOH (LIQUID)LOCALCoMat 01-572
CoMat 01-575 AQUEOUS CLEANERLOCALCoMat 01-575
CoMat 01-577 AQUEOUS CLEANER94058CoMat 01-577
CoMat 01-581 TURBINE AIRFOIL CLEANER08ZP2CoMat 01-581
CoMat 01-582 AQUEOUS-BASED CARBON REMOVER71410CoMat 01-582
CoMat 01-583 ALKALINE RUST REMOVER (LIQUID)LOCALCoMat 01-583
CoMat 01-584 DEOXIDIZER, NEUTRAL35502CoMat 01-584
CoMat 01-589 POTASSIUM HYDROXIDE, LIQUID, 44-46%LOCALCoMat 01-589
CoMat 01-590 POTASSIUM HYDROXIDE, LIQUID, 26-28 WEIGHT PERCENTLOCALCoMat 01-590
CoMat 05-022 ALUMINUM OXIDE ABRASIVE62596CoMat 05-022
CoMat 05-166 GLASS BEAD04UX7CoMat 05-166
CoMat 05-198 ALUMINUM OXIDE, 320-GRITIE531CoMat 05-198
CoMat 05-199 ALUMINUM OXIDE, F500 GRITIE531CoMat 05-199
CoMat 10-097 CORROSION INHIBITOR,(NON-NITRITE)LOCALCoMat 10-097
CoMat 10-099 CORROSION INHIBITOR,WATER SOLUBLE71410CoMat 10-099
CoMat 10-134 CORROSION INHIBITOR,(NON-NITRITE)35502CoMat 10-134
CoMat 10-135 CORROSION INHIBITOR71410CoMat 10-135

Spares

NONE

Safety Requirements

WARNING

IT IS THE RESPONSIBILITY OF THE OPERATOR TO OBTAIN AND OBSERVE THE CONSUMABLE MATERIAL MANUFACTURER'S SAFETY DATA SHEETS FOR CONSUMABLE MATERIAL SAFETY INFORMATION (SUCH AS, HAZARDOUS INGREDIENTS, PHYSICAL/CHEMICAL CHARACTERISTICS, FIRE HAZARD DATA, EXPLOSION HAZARD DATA, REACTIVITY HAZARD DATA, HEALTH HAZARD DATA, PRECAUTIONS FOR SAFE HANDLING, USE AND CONTROL MEASURES). AND ALSO TO TAKE LOCAL REGULATIONS INTO CONSIDERATION.

WARNING

CARE MUST BE TAKEN WHEN YOU ADD COMPOUNDS THAT CONTAIN SOLID SODIUM HYDROXIDE TO WATER, BECAUSE HEAT IS GIVEN OUT WHEN THE COMPOUND DISSOLVES. WHILE YOU ADD THE COMPOUND TO THE SOLUTION, THERE MUST BE STRONG MOVEMENT OF THE SOLUTION TO PREVENT HIGH CONCENTRATIONS OF THE COMPOUND IN SMALL AREAS OF THE TANK, WHICH CAN CAUSE THE SOLUTION TO BOIL.

Procedure

    1. SUBTASK 70-11-48-110-000 Equipment and Material

    1. Standard equipment - none

    2. Refer to the applicable subtask for the consumable materials that are necessary to do the solution make-up and maintenance for the specified Solution Code. To identify the consumable materials, refer to the V2500 Consumable Materials Index (Publications Ref. PCI-V2500 1IA).

    2. SUBTASK 70-11-48-110-001 Solution Code 1 - Caustic Potassium Permanganate Descaling Solution

      1. Composition of the solution.

        1. Use Solution Code 1A or Solution Code 1B:

        1. Solution Code 1A

          Material or Solution Parameter

          Make-Up

          Operating Limits

          25 oz. wt./gal (187.5 g/l)

          20 oz. wt./gal to 30 oz. wt./gal (150 g/l to 225 g/l)

          10 oz. wt./gal (75 g/l)

          6 oz. wt./gal to 12 oz. wt./gal (45 g/l to 90 g/l)

        2. Solution Code 1B

          Material or Solution Parameter

          Make-Up

          Operating Limits

          10 oz. wt./gal (75 g/l)

          6 oz. wt./gal to 12 oz. wt./gal (45 g/l to 90 g/l)

          0.245 wt./gal (0.245 g/l) (24.5 percent by volume)

          -

          Sodium Hydroxide NaOH

          -

          20 oz. wt./gal to 30 oz. wt./gal (150 g/l to 225 g/l)

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of the operating level.

      2. WARNING

        USE EXTREME CARE WHEN YOU ADD SODIUM HYDROXIDE BECAUSE AS THE CONCENTRATION IS INCREASED, CONSIDERABLE HEAT IS GIVEN OFF.

        Slowly and carefully, while you stir, add the necessary quantity of the sodium hydroxide flakes or the liquid sodium hydroxide.

        NOTE

        The potassium permanganate will dissolve more easily when the temperature of the solution is in this range.

      3. If necessary, increase the temperature of the solution to 130 deg F to 150 deg F (54 deg C to 60 deg C) and then add the necessary quantity of the potassium permanganate.

      4. Fill the tank to 100 percent of the operating level with water and increase the temperature of the solution to the temperature specified in the cleaning procedure, and stir to mix.

      3. Solution maintenance.

      1. To do the maintenance of the solution, refer to SPM TASK 70-11-47-110-501, SUBTASK 70-11-47-170-012, SUBTASK 70-11-47-180-025 (P-55 Test Method).

  3. SUBTASK 70-11-48-110-002 Solution Code 2 - Alkaline Permanganate Solution - Deleted

    4. SUBTASK 70-11-48-110-004 Solution Code 4 - Alkali Cleaner (General Purpose) Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      25 percent by volume

      20 to 30 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to approximately 50 percent of the operating level.

      2. Slowly and carefully add the necessary quantity of the alkali cleaner and mix fully.

      3. Fill the tank with water to 100 percent of the operating level. Increase the temperature of the solution to the temperature specified in the cleaning procedure, and stir to mix.

      3. Solution maintenance.

      1. To do the maintenance of the solution, refer to SPM TASK 70-11-47-110-501, SUBTASK 70-11-47-170-012, SUBTASK 70-11-47-180-015 (P-6 Test Method).

  5. SUBTASK 70-11-48-110-005 Solution Code 5 - Alkaline Rust Remover Solution - Deleted

  6. SUBTASK 70-11-48-110-006 Solution Code 6 - Alkaline Rust Remover Solution - Deleted

  7. SUBTASK 70-11-48-110-007 Solution Code 7 - Alkaline Rust Remover Solution - Deleted

  8. SUBTASK 70-11-48-110-008 Solution Code 8 - Acidic Scale Conditioner Solution - Deleted

  9. SUBTASK 70-11-48-110-009 Solution Code 9 - Acidic Scale Conditioner Solution - Deleted

    10. SUBTASK 70-11-48-110-010 Solution Code 10 - Wet Abrasive Solution

      1. Concentration of the solution.

        This is an aqueous solution at a concentration of 5 lbs/gal (600 g/l) of CoMat 05-022 ALUMINUM OXIDE ABRASIVE (240-grit) or CoMat 05-198 ALUMINUM OXIDE, 320-GRIT (320-grit) and 4 oz.wt of CoMat 01-207 ANTISOLIDIFYING COMPOUND to 50 lbs. of abrasive(5 g of anti-solidifying compound for each one kg of abrasive) and 15 ml/gal (4 ml/l) of one of the corrosion inhibitors in Table.

      1. The corrosion inhibitor is optional if the blasting equipment is made of stainless steel.

        Table 5.

        Corrosion Inhibitor (non-nitrate)

        Corrosion Inhibitor (non-nitrate)

        Corrosion Inhibitor (non-nitrate)

        Corrosion Inhibitor (non-nitrate)

        Corrosion Inhibitor (non-nitrate)

      2. Make-up of the solution.

      1. Fill the tank with water to approximately 75 percent of the operating level.

      2. With the pump on, slowly add the necessary quantity of CoMat 05-022 ALUMINUM OXIDE ABRASIVE (240 grit) or CoMat 05-198 ALUMINUM OXIDE, 320-GRIT (320-grit).

        3. Add the necessary quantities of anti-solidifying compound and corrosion inhibitor.

        1. The corrosion inhibitor is optional if the blasting equipment is made of stainless steel.

      4. Fill the tank with water to 100 percent of the operating level.

      5. Let the slurry mix freely for two to three minutes before you operate the machine.

      3. Slurry maintenance.

        1. After each four hours that the machine operates, examine the abrasive content of the solution as follows:

        1. Fill a 100 ml or 500 ml graduated cylinder with a sample of slurry as it leaves the gun.

        2. The slurry must sit to let the media settle to the bottom of the graduated cylinder.

        3. Keep a record of the results in a department log book before the next periodic check.

        2. Keep the abrasive content of the slurry at approximately 30 to 40 percent by volume. Add three milliliters of corrosion inhibitor for each pound of abrasive added (or, 6.6 ml of corrosion inhibitor for each one kg of abrasive). Add 0.5 oz of anti-solidifying compound for each six pounds of abrasive added (5.2 g of anti-solidifying compound for each one kg of added abrasive).

        1. The corrosion inhibitor is optional if the blasting equipment is made of stainless steel.

  11. SUBTASK 70-11-48-110-011 Solution Code 11 - Alkaline Rust Remover Solution - Deleted

  12. SUBTASK 70-11-48-110-012 Solution Code 12 - Alkaline Permanganate Solution - Deleted

  13. SUBTASK 70-11-48-110-013 Solution Code 13 - Acidic Scale Conditioner Solution - Deleted

    14. SUBTASK 70-11-48-110-014 Solution Code 14 - Inhibited Phosphoric Acid

    1. Composition of the solution.

      Table 6.

      Material

      Make-Up

      Operating Limits

      50 percent by volume

      45 to 50 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of the operating level.

      2. Slowly and carefully add an equal amount of the inhibited phosphoric acid, and stir to mix. Use at room temperature.

        NOTE

        For most effective results, the solution temperature must not be unusually low.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  15. SUBTASK 70-11-48-110-015 Solution Code 15 - Alkaline Rust Remover Solution - Deleted

  16. SUBTASK 70-11-48-110-016 Solution Code 16 - Alkaline Rust Remover Solution - Deleted

  17. SUBTASK 70-11-48-110-017 Solution Code 17 - Alkaline Rust Remover Solution - Deleted

  18. SUBTASK 70-11-48-110-018 Solution Code 18 - Acidic Scale Conditioner Solution - Deleted

  19. SUBTASK 70-11-48-110-019 Solution Code 19 - Alkaline Rust Remover Solution - Deleted

    20. SUBTASK 70-11-48-110-020 Solution Code 20 - Alkaline Rust Remover Solution

    1. Composition of the solution.

      Table 7.

      Material

      Make-Up

      Operating Limits

      -

      See solution maintenance.

      48 fl. oz./gal (369.6 ml/l) (37 percent by volume)

      30 to 37 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of the operating level.

      2. Slowly and carefully add the necessary quantity of the alkaline rust remover.

      3. Stir to mix and fill the tank with water to 85 percent of the operating level.

      4. Increase the temperature of the solution to the temperature specified in the cleaning procedure.

      5. Fill the tank with water to 100 percent of the operating level, keep the temperature specified in the cleaning procedure, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution with the specified additive.

    21. SUBTASK 70-11-48-110-021 Solution Code 21 - Alkali Cleaner (General Purpose) Solution

    1. Composition of the solution.

      Table 8.

      Material

      Make-Up

      Operating Limits

      25 percent by volume

      15 to 25 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of the operating level.

      2. Slowly and carefully add the necessary quantity of the alkali cleaner, and stir to mix.

      3. Fill the tank with water to 100 percent of the operating level, increase the temperature of the solution to the temperature specified in the cleaning procedure and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

      2. Discard the solution when cleaning can no longer be done within the time specified by the cleaning procedure.

    22. SUBTASK 70-11-48-110-022 Solution Code 22 - Alkali Cleaner (General Purpose) Solution

    1. Composition of the solution.

      Table 9.

      Material

      Make-Up

      Operating Limits

      25 percent by volume

      15 to 25 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of the operating level.

      2. Slowly and carefully add the necessary quantity of the alkali cleaner, and stir to mix.

      3. Fill the tank with water to 100 percent of the operating level, increase the temperature of the solution to the temperature specified in the cleaning procedure and stir to mix.

      3. Solution maintenance.

      1. Discard the solution when cleaning can no longer be done within the time specified by the cleaning procedure.

    23. SUBTASK 70-11-48-110-023 Solution Code 23 - Alkaline Rust Remover Solution

    1. Composition of the solution.

      Table 10.

      Material

      Make-Up

      Operating Limits

      50 percent by volume

      40 to 50 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of the operating level.

      2. Slowly and carefully add the necessary quantity of the alkaline rust remover, and stir to mix.

      3. Fill the tank with water to 100 percent of the operating level, keep the solution at the temperature specified in the cleaning procedure and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    24. SUBTASK 70-11-48-110-024 Solution Code 24 - Alkaline Rust Remover Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      75 percent by volume

      63 to 75 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of the operating level.

      2. Slowly and carefully add the necessary quantity of the alkaline rust remover, and stir to mix.

      3. Fill the tank with water to 100 percent of the operating level.

      4. Increase the temperature of the solution to the temperature specified in the cleaning procedure, keep to the temperature specified in the cleaning procedure and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    25. SUBTASK 70-11-48-110-025 Solution Code 25 - Alkaline Rust Remover Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      35 percent by volume

      20 to 30 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to approximately 50 percent of the operating level.

      2. Slowly and carefully add the necessary quantity of CoMat 01-583 ALKALINE RUST REMOVER (LIQUID).

      3. Stir to mix.

      4. Fill the tank with water to 100 percent of the operating level.

      5. Stir to mix.

      6. Increase the solution temperature to the specified operating temperature range in the cleaning procedure. Keep the solution in this temperature range.

      3. Solution Maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    26. SUBTASK 70-11-48-110-026 Solution Code 26 - Wet Abrasive Compound Novaculite Slurry Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      CoMat 01-202 WET ABRASIVE COMPOUND (No. 325 Novaculite) or CoMat 01-204 WET ABRASIVE COMPOUND (No. 200 Novaculite)

      4 lbs/gal to 6 lbs/gal (480 g/l to 720 g/l)

      20 to 30 percent by volume

      4 oz. wt./50 lbs of abrasive (5 g/kg of abrasive)

      See solution maintenance.

      15 ml/gal

      See solution maintenance.

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to approximately 75 percent of the operating level.

      2. With the pump operating, slowly add the necessary quantity of the wet abrasive compound.

        NOTE

        It is not necessary to use corrosion inhibitor if the blast equipment is made of stainless steel.

      3. Add the necessary quantities of the anti-solidifying compound and the corrosion inhibitor.

      4. Fill the tank with water to 100 percent of the operating level.

      5. Let the slurry mix freely for two to three minutes before you operate the machine.

      3. Solution maintenance.

        1. Measure the abrasive content of the slurry solution at least two times each day.

        1. Collect a 100 ml or 500 ml sample of the slurry in a graduated cylinder. Collect the sample directly from the blast cabinet gun while the blast cabinet operates.

        2. The slurry sample in the graduated cylinder must sit for 15 to 30 minutes to let the media settle to the bottom of the graduated cylinder.

        3. Record the total volume of the sample in the graduated cylinder and the volume of the solids in the graduated cylinder. Record the results in a department log book before the next periodic check.

        2. If the abrasive content is not in the specified range, do the subsequent procedure to adjust the solution. Keep records of all solution adjustments.

          NOTE

          It is not necessary to use corrosion inhibitor if the blast equipment is made of stainless steel.

        1. Add the necessary quantity of the wet abrasive compound.

        2. Add three milliliters of the corrosion inhibitor for each pound of added wet abrasive compound (6.6 ml of the corrosion inhibitor for each kilogram of added wet abrasive compound). Add 0.5 oz.wt. of the anti-solidifying compound for each six pounds of added wet abrasive compound (5.2 g of the anti-solidifying compound for each kilogram of added wet abrasive compound).

    27. SUBTASK 70-11-48-110-027 Solution Code 72 - Alkaline Rust Remover Solution - Deleted

    1. Refer to Solution Code 97 (Step).

  28. SUBTASK 70-11-48-110-028 Solution Code 73 - Alkali Cleaner (General Purpose) - Deleted

  29. SUBTASK 70-11-48-110-029 Solution Code 74 - Alkali Cleaner (General Purpose, Low Foam) Solution - Deleted

    30. SUBTASK 70-11-48-110-030 Solution Code 75 - Alkali Cleaner (General Purpose, Low Foam) Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      10 percent by volume

      5 to 10 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean water to 50 percent of the operating level.

      2. Slowly and carefully add the necessary quantity of the low-foam general purpose alkali cleaner. Mix fully.

      3. Fill the tank to 100 percent of its operating volume with clean cold tap water.

      4. Increase the temperature of the solution to the temperature specified in the cleaning procedure, and stir to mix.

      5. Continually agitate the solution by mechanical methods.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  31. SUBTASK 70-11-48-110-031 Solution Code 76 - Alkali Cleaner (General Purpose, Low Foam) Solution - Deleted

  32. SUBTASK 70-11-48-110-032 Solution Code 77 - Alkali Cleaner (General Purpose, Low Foam) Solution - Deleted

    33. SUBTASK 70-11-48-110-033 Solution Code 78 - Alkaline Rust Remover Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      35 percent by volume

      30 to 35 percent by volume

      2. Make-up of the solution.

      1. Fill the tank to 50 percent of the operating volume with cold water.

      2. Slowly and carefully add necessary quantity of the alkaline rust remover.

      3. Stir to mix and fill to 85 percent of the tank with water.

      4. Increase the temperature of the solution to the temperature specified in the cleaning procedure.

      5. Fill the remaining volume of the tank with tap water and keep the specified temperature. Stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    34. SUBTASK 70-11-48-110-034 Solution Code 79 - Alkaline Rust Remover Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      45 percent by volume

      40 to 45 percent by volume

      2. Make-up of the solution.

      1. Fill the tank to 50 percent of the operating volume with cold water.

      2. Slowly and carefully add necessary quantity of the alkaline rust remover.

      3. Stir to mix and fill to 85 percent of the tank with water.

      4. Increase the temperature of the solution to the temperature specified in the cleaning procedure.

      5. Fill the remaining volume of the tank with tap water and keep the specified temperature. Stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  35. SUBTASK 70-11-48-110-035 Solution Code 80 - Corrosion Inhibitor Solution - Deleted

    36. SUBTASK 70-11-48-110-036 Solution Code 91 - Acidic Scale Conditioner Solution

    1. Concentration of the solution.

      Material or Solution Parameter

      Make-Up

      Operating Limits

      As necessary to adjust solution pH

      -

      20 percent by volume

      15 to 20 percent by volume

      Solution pH

      -

      3.0 to 3.5

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of the operating level.

      2. Slowly and carefully add the necessary quantity of the acid scale conditioner, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning procedure.

      4. Fill the tank with water to 100 percent of the operating level, keep to the temperature specified in the cleaning procedure, and stir to mix.

      5. Do a check of the solution pH and adjust as necessary with the nitric acid.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    37. SUBTASK 70-11-48-110-037 Solution Code 92 - Corrosion Inhibitor Solution

      1. General.

      1. Use Solution Code 92 only for temporary corrosion protection.

      2. Do not use the solution on engine bearings.

      3. Do not use air agitation for more than five minutes before you use, or do a test of, the solution.

      4. Do not use air agitation when the solution is in operation.

    2. Composition of the solution.

      Table 18.

      Material

      Make-Up

      1.0 percent by volume

      3. Make-up of the solution.

      1. Fill the tank to 99 percent of its operating level with water, then fill the remaining volume of the tank with the non-nitrite corrosion inhibitor.

        NOTE

        This solution can be made up in a spray container for local application. It is necessary to shake the container before you apply the solution.

      2. Mix by mechanical agitation or air agitation for five minutes maximum. Do not continue to use air agitation after completion of the make-up of the solution.

      4. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

      2. Change the solution one time each month or when there is contamination of the solution.

      3. Use the solution at ambient temperature upto 150 deg F (66 deg C).

      4. Do not use air agitation when the solution is in operation.

  38. SUBTASK 70-11-48-110-038 Solution Code 93 - Corrosion Inhibitor Solution - Deleted

    39. SUBTASK 70-11-48-110-039 Solution Code 94 - Corrosion Inhibitor Solution

      1. General.

      1. Use Solution Code 94 only for temporary corrosion protection.

      2. Do not use the solution on engine bearings.

      3. Do not use air agitation for more than five minutes before you use, or do a test of, the solution.

      4. Do not use air agitation when the solution is in operation.

    2. Composition of the solution.

      Material

      Make-Up

      1.0 percent by volume

      3. Make-up of the solution.

      1. Fill the tank to 99 percent of its operating level with water, then fill the remaining volume of the tank with the non-nitrite corrosion inhibitor.

        NOTE

        This solution can be made up in a spray container for local application. It is necessary to shake the container before you apply the solution.

      2. Mix by mechanical agitation or air agitation for five minutes maximum. Do not continue to use air agitation after completion of the make-up of the solution.

      4. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

      2. NOTE

        If the solution is premixed in a sprayer, the monthly disposal does not apply.

        Change the solution one time each month or when there is a contamination of the solution.

      3. Use the solution at ambient temperature upto 200 deg F (93 deg C).

      4. Do not use air agitation when the solution is in operation.

  40. SUBTASK 70-11-48-110-040 Solution Code 95 - Acidic Scale Conditioner Solution - Deleted

    41. SUBTASK 70-11-48-110-041 Solution Code 96 - Acidic Scale Conditioner Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      30 percent by volume

      25 to 30 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of the operating level.

      2. Slowly and carefully add the specified amount of the acid scale conditioner, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning procedure.

      4. Fill the tank with water to 100 percent of the operating level, keep the temperature specified in the cleaning procedure, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    42. SUBTASK 70-11-48-110-042 Solution Code 97 - Alkaline Rust Remover Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      40 percent by volume

      30 to 40 percent by volume

      -

      Refer to solution maintenance.

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of the operating level.

      2. Heat to 150 deg F to 160 deg F (66 deg C to 71 deg C).

      3. Slowly and carefully add the specified amount of the alkaline rust remover. Stir to mix.

      4. Increase the temperature of the solution to the temperature specified in the cleaning procedure.

      5. Fill the tank with water to 100 percent of operating level, keep the temperature specified in cleaning procedure, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution with the alkaline rust remover additive.

  43. SUBTASK 70-11-48-110-043 Solution Code 98 - Alkaline Rust Remover Solution - Deleted

  44. SUBTASK 70-11-48-110-044 Solution Code 99 - Alkaline Rust Remover Solution - Deleted

    45. SUBTASK 70-11-48-110-045 Solution Code 100 - Alkaline Permanganate Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      100 percent by volume

      -

      -

      11.2 - 16.8 percent by volume

      -

      6.0 to 14 percent by volume

      2. Make-up of the solution.

      1. Slowly and carefully fill the tank to 50 percent of the operating level with the alkaline permanganate liquid.

      2. Increase the temperature of the solution to the temperature specified in the cleaning procedure.

      3. Fill the tank with the alkaline permanganate liquid to 100 percent of the operating level, keep the temperature specified in the cleaning procedure and stir to mix.

      3. Solution maintenance.

      1. Use the alkaline permanganate caustic additive and the permanganate additive to do the maintenance of the solution. Refer to the manufacturer's instructions.

  46. SUBTASK 70-11-48-110-046 Solution Code 101 - Alkaline Permanganate Solution - Deleted

  47. SUBTASK 70-11-48-110-047 Solution Code 103 - Alkaline Rust Remover Solution - Deleted

  48. SUBTASK 70-11-48-110-048 Solution Code 104 - Alkaline Rust Remover Solution - Deleted

  49. SUBTASK 70-11-48-110-049 Solution Code 105 - Alkaline Rust Remover Solution - Deleted

    50. SUBTASK 70-11-48-110-050 Solution Code 106 - Alkaline Rust Remover Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      20 percent by volume

      15 to 20 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with water to 50 percent of the operating volume.

      2. Slowly and carefully add the necessary amount of the alkaline rust remover. Stir to mix.

      3. Fill the tank with water to 100 percent of its operating volume, and stir to mix.

      4. Increase the temperature of the solution to the temperature specified in the cleaning process, keep the solution at the specified temperature, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  51. SUBTASK 70-11-48-110-051 Solution Code 107 - Alkaline Rust Remover Solution - Deleted

    52. SUBTASK 70-11-48-110-052 Solution Code 108 - Alkaline Rust Remover Solution

    1. Concentration of the solution.

      Material

      Make-Up

      Operating Limits

      13 percent by volume

      9 to 13 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with water to 50 percent of the operating volume.

      2. Slowly and carefully add the necessary amount of the alkaline rust remover. Stir to mix.

      3. Fill the tank with water to 100 percent of its operating volume, and stir to mix.

      4. Increase the temperature of the solution to the temperature specified in the cleaning process, keep the solution at the specified temperature, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    53. SUBTASK 70-11-48-110-053 Solution Code 109 - Alkaline Rust Remover Solution

    1. Concentration of the solution.

      Material

      Make-Up

      Operating Limits

      18 percent by volume

      12 to 18 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with water to 50 percent of the operating volume.

      2. Slowly and carefully add the necessary amount of the alkaline rust remover. Stir to mix.

      3. Fill the tank with water to 100 percent of its operating volume, and stir to mix.

      4. Increase the temperature of the solution to the temperature specified in the cleaning process, keep the solution at the specified temperature, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  54. SUBTASK 70-11-48-110-054 Solution Code 110 - Alkaline Rust Remover Solution - Deleted

    55. SUBTASK 70-11-48-110-055 Solution Code 111 - Alkaline Rust Remover Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      20 percent by volume

      12 to 20 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with water to 50 percent of the operating volume.

      2. Slowly and carefully add the necessary amount of the alkaline rust remover. Stir to mix.

      3. Fill the tank with water to 100 percent of its operating volume, and stir to mix.

      4. Increase the temperature of the solution to the temperature specified in the cleaning process, keep the solution at the specified temperature, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  56. SUBTASK 70-11-48-110-056 Solution Code 112 - Alkaline Rust Remover Solution - Deleted

    57. SUBTASK 70-11-48-110-057 Solution Code 113 - Glass Bead Abrasive Solution

    1. Concentration of the solution.

      Material

      Make-Up

      Operating Limits

      5 lbs/gal to 8 lbs/gal (600 g/l to 960 g/l)

      40 to 60 percent by volume

      Anti-solidifying Compound CoMat 01-207 ANTISOLIDIFYING COMPOUND

      4 oz. wt./50 lbs of abrasive (5 g/kg of abrasive)

      See solution maintenance.

      15 ml/gal

      See solution maintenance.

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 75 percent of the operating volume.

      2. With the pump in operation, slowly add the necessary amount of the glass bead peening media.

        NOTE

        It is not necessary to use corrosion inhibitor if the blast equipment is made of stainless steel.

      3. Add the necessary amounts of the anti-solidifying compound and the non-nitrite corrosion inhibitor.

      4. Fill the tank to 100 percent of its operating volume. Permit the slurry to fully mix for two to three minutes before you operate the machine.

      3. Maintenance of the slurry.

        1. Do a check of the abrasive content of the slurry a minimum of two times each day.

        1. Collect a 500 milliliter sample of the slurry in a graduated cylinder. Collect the sample directly from the blast cabinet gun while the blast cabinet operates.

        2. The slurry sample in the graduated cylinder must sit for 15 to 30 minutes to let the media settle to the bottom of the graduated cylinder.

        2. Keep the abrasive content at 40 to 60 percent by volume.

          NOTE

          It is not necessary to use corrosion inhibitor if the blast equipment is made of stainless steel.

        1. Add the necessary quantity of the glass bead peening media.

        2. Add three milliliters of the non-nitrite corrosion inhibitor for each pound of added glass bead peening media (6.6 ml of the non-nitrite corrosion inhibitor for each kilogram added of glass bead peening media).

        3. Add 0.5 oz.wt. of the anti-solidifying compound for each six pounds of added glass bead peening media (5.2 g of the anti-solidifying compound for each kilogram added of glass bead peening media).

    58. SUBTASK 70-11-48-110-058 Solution Code 114 - Alkali Cleaner (General Purpose, Low Foam) Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      30 percent by volume

      20 to 30 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the low-foam general purpose alkali cleaner, and stir to mix.

      3. Fill the remaining operating volume of the tank with water.

      4. Increase the temperature of the solution to the temperature in the cleaning process, and stir to mix. Keep the solution at this temperature.

      5. Continually shake the solution by mechanical methods.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    59. SUBTASK 70-11-48-110-059 Solution Code 115 - Aqueous Cleaner Solution (Low Foam)

    1. Superseded by Solution Code 124 (Step).

  60. SUBTASK 70-11-48-110-060 Solution Code 116 - Aqueous Degreaser Solution - Deleted

    61. SUBTASK 70-11-48-110-061 Solution Code 117 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      25 percent by volume

      20 to 25 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser. Stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the remaining operating volume of the tank with water, and stir to mix. Keep the solution at the specified temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    62. SUBTASK 70-11-48-110-062 Solution Code 119 - Acidic Scale Conditioner Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      25 percent by volume

      20 to 25 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the acid scale conditioner, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning procedure.

      4. Fill the tank with water to 100 percent of the operating level of the tank, keep the temperature specified in the cleaning procedure, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    63. SUBTASK 70-11-48-110-063 Solution Code 120 - Alkaline Rust Remover Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      35 percent by volume

      30 to 35 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the alkaline rust remover, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning procedure.

      4. Fill the tank with water to 100 percent of the operating level of the tank, keep the temperature specified in the cleaning procedure, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  64. SUBTASK 70-11-48-110-064 Solution Code 121 - Alkaline Rust Remover Solution - Deleted

  65. SUBTASK 70-11-48-110-065 Solution Code 122 - Alkaline Cleaner Solution - Deleted

    66. SUBTASK 70-11-48-110-066 Solution Code 123 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      25 percent by volume

      15 to 25 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the remaining operating volume of the tank with water, and stir to mix. Keep the solution at this temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    67. SUBTASK 70-11-48-110-067 Solution Code 124 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      10 percent by volume

      5 to 10 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the remaining operating volume of the tank with water, and stir to mix. Keep the solution at the specified temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    68. SUBTASK 70-11-48-110-068 Solution Code 125 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      25 percent by volume

      15 to 25 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the remaining operating volume of the tank with water, and stir to mix. Keep the solution at the specified temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    69. SUBTASK 70-11-48-110-069 Solution Code 126 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      20 percent by volume

      10 to 20 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the remaining operating volume of the tank with water, and stir to mix. Keep the solution at the specified temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    70. SUBTASK 70-11-48-110-070 Solution Code 127 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      50 percent by volume

      25 to 50 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the remaining operating volume of the tank with water, and stir to mix. Keep the solution at the specified temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    71. SUBTASK 70-11-48-110-071 Solution Code 128 - Aqueous Cleaner Solution (Low Foam)

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      10 percent by volume

      5 to 10 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the low-foam aqueous degreaser, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the remaining operating volume of the tank with water, and stir to mix. Keep the solution at the specified temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  72. SUBTASK 70-11-48-110-072 Solution Code 129 - Aqueous Degreaser Solution - Deleted

    73. SUBTASK 70-11-48-110-073 Solution Code 130 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      10 percent by volume

      5 to 10 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the tank with water to 100 percent of its operating volume, and stir to mix. Keep the solution at the specified temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    74. SUBTASK 70-11-48-110-074 Solution Code 131 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      10 percent by volume

      5 to 10 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the tank with water to 100 percent of its operating volume, and stir to mix. Keep the solution at the specified temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    75. SUBTASK 70-11-48-110-075 Solution Code 132 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      10 percent by volume

      5 to 10 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the tank with water to 100 percent of its operating volume, and stir to mix. Keep the solution at the specified temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    76. SUBTASK 70-11-48-110-076 Solution Code 133 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      33 percent by volume

      25 to 33 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the tank with water to 100 percent of its operating volume, and stir to mix. Keep the solution at the specified temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    77. SUBTASK 70-11-48-110-077 Solution Code 134 - Aqueous Cleaner Solution (Low Foam)

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      20 percent by volume

      15 to 20 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the low-foam aqueous cleaner, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the tank with water to 100 percent of its operating volume, and stir to mix. Keep the solution at the specified temperature specified.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  78. SUBTASK 70-11-48-110-078 Solution Code 139 - Alkaline Rust Remover Solution - Deleted

    79. SUBTASK 70-11-48-110-079 Solution Code 140 - Alkaline Permanganate Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      25 percent by volume

      15 to 25 percent by volume

      25 percent by volume

      15 to 25 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean cold water to 40 percent of its operating volume.

      2. Slowly and carefully add the necessary equal amounts of the alkaline permanganate Part 1 and the alkaline permanganate Part 2. Stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the tank with water to 100 percent of its operating volume, and stir to mix. Keep the solution at the specified temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  80. SUBTASK 70-11-48-110-080 Solution Code 141 - Alkaline Permanganate Solution - Deleted

    81. SUBTASK 70-11-48-110-081 Solution Code 142 - Corrosion Inhibitor Solution

      1. General.

      1. Use Solution Code 142 for temporary corrosion protection only.

      2. Do not use this solution on engine bearings.

    2. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      Corrosion Inhibitor, Water Soluble CoMat 01-502 CORROSION INHIBITOR (WATER SOLUBLE)

      0.50 percent by volume

      0.25 to 0.50 percent by volume

      3. Make-up of the solution.

      1. Fill the tank with clean cold water to 99 percent of its operating volume; then fill the remaining volume of the tank with the watersoluble corrosion inhibitor.

        NOTE

        This solution can be made up in a spray container for local application. It is necessary to shake the container before you apply the solution.

      2. CAUTION

        IF YOU USE AIR AGITATION FOR MORE THAN FIVE MINUTES, THE CHEMISTRY OF THE SOLUTION CAN CHANGE AND CAUSE THE SOLUTION PERFORMANCE TO BE UNSATISFACTORY.

        Mix by mechanical agitation or air agitation for five minutes maximum. Do not continue to use air agitation after completion of the make-up of the solution.

      4. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

      2. Change the solution one time each month or when there is contamination of the solution.

        NOTE

        If the solution is premixed in a sprayer, the monthly disposal does not apply.

      3. Use this solution at ambient temperature upto 170 deg F (77 deg C).

      4. Do not use air agitation after completion of the make-up of the solution.

    82. SUBTASK 70-11-48-110-082 Solution Code 143 - Corrosion Inhibitor Solution

      1. General.

      1. Use Solution Code 143 for temporary corrosion protection only.

      2. Do not use this solution on engine bearings.

    2. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      2 percent by volume

      1 to 2 percent by volume

      3. Make-up of the solution.

      1. Fill the tank with clean cold water to 98 percent of its operating volume; then fill the remaining volume of the tank with the watersoluble corrosion inhibitor.

        NOTE

        This solution can be made up in a spray container for local application. It is necessary to shake the container before you apply the solution.

      2. CAUTION

        IF YOU USE AIR AGITATION FOR MORE THAN FIVE MINUTES, THE CHEMISTRY OF THE SOLUTION CAN CHANGE AND CAUSE THE SOLUTION PERFORMANCE TO BE UNSATISFACTORY.

        Mix by mechanical agitation or air agitation for five minutes maximum. Do not continue to use air agitation after completion of the make-up of the solution.

      4. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

      2. Change the solution one time each month or when there is contamination of the solution.

        NOTE

        If the solution is premixed in a sprayer, the monthly disposal does not apply.

      3. Use this solution at ambient temperature upto 190 deg F (88 deg C).

      4. Do not use air agitation after completion of the make-up of the solution.

  83. SUBTASK 70-11-48-110-083 Solution Code 144 - Alkaline Rust Remover Solution - Deleted

  84. SUBTASK 70-11-48-110-084 Solution Code 145 - Alkaline Rust Remover Solution - Deleted

    85. SUBTASK 70-11-48-110-085 Solution Code 149 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      30 percent by volume

      20 to 30 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the remaining volume of the tank with clean water, keep the solution at the specified temperature, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    86. SUBTASK 70-11-48-110-086 Solution Code 157 - Aqueous Cleaner Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      30 percent by volume

      20 to 30 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser, and stir to mix.

      3. Fill the tank with clean water to 100 percent of its operating volume.

      4. Increase the temperature of the solution to the temperature specified by the cleaning process, and stir to mix. Keep the solution at this temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    87. SUBTASK 70-11-48-110-087 Solution Code 158 - Aqueous Cleaner Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      10 percent by volume

      5 to 10 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous cleaner, and stir to mix.

      3. Fill the tank with clean water to 100 percent of its operating volume.

      4. Increase the temperature of the solution to the temperature specified by the cleaning process, and stir to mix. Keep the solution at this temperature.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  88. SUBTASK 70-11-48-110-088 Solution Code 159 - Acidic Scale Conditioner Solution - Deleted

    89. SUBTASK 70-11-48-110-089 Solution Code 160 - Acidic Scale Conditioner Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      20 percent by volume

      15 to 20 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with cold water to 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the acid scale conditioner, and stir to mix.

      3. Increase the temperature of the solution to the temperature specified in the cleaning process.

      4. Fill the tank with clean water to 100 percent of its operating volume, keep the solution at the specified temperature, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    90. SUBTASK 70-11-48-110-090 Solution Code 161 - Alkaline Permanganate Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      -

      See solution maintenance.

      100 percent by volume

      65 to 100 percent by volume

      2. Make-up of the solution.

      1. Slowly and carefully fill the tank to 50 percent of its operating volume with the alkaline permanganate liquid.

      2. Increase the temperature of the solution to the temperature specified in the cleaning process.

      3. Slowly and carefully fill the remaining volume of the tank with the alkaline permanganate liquid. Keep the solution at the temperature specified in the cleaning process.

      3. Solution maintenance.

      1. Use the alkaline permanganate liquid and the alkaline permanganate additive to do the maintenance of the solution. Refer to the manufacturer's instructions.

    91. SUBTASK 70-11-48-110-091 Solution Code 162 - Alkaline Permanganate Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      50 percent by volume

      30 to 50 percent by volume

      25 percent by volume

      15 to 25 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with clean water to 20 percent of its operating volume.

      2. Slowly and carefully add the necessary quantities of the caustic component and the permanganate concentrate component of the alkaline permanganate liquid. Stir to mix.

      3. Fill the tank with clean water to 100 percent of its operating volume, and stir to mix.

      4. Increase the temperature of the solution to the temperature specified by the cleaning process. Keep the solution at this temperature.

      3. Solution maintenance.

      1. Use the caustic component and the permanganate concentrate component of the alkaline permanganate liquid to do the maintenance of the solution. Refer to the manufacturer's instructions.

    92. SUBTASK 70-11-48-110-092 Solution Code 168 - Alkaline Permanganate Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      25 percent by volume

      15 to 25 percent by volume

      25 percent by volume

      15 to 25 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with cold water to 40 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the caustic component of the alkaline permanganate liquid while you stir to mix.

      3. Slowly and carefully add the necessary amount of the permanganate component of the alkaline permanganate liquid.

      4. Fill the remaining operating volume of the tank with tap water, and stir to mix.

      5. Increase the temperature of the solution to the temperature specified by the cleaning process.

      3. Solution maintenance.

      1. Use the caustic component and the permanganate component of the alkaline permanganate liquid to do the maintenance of the solution. Refer to the manufacturer's instructions.

    93. SUBTASK 70-11-48-110-093 Solution Code 171 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      10 percent by volume

      5 to 10 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with cold water to approximately 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser.

      3. Stir to mix the solution.

      4. Increase the solution temperature to the temperature specified by the cleaning process.

      5. Fill the remaining volume of the tank with tap water but make sure to keep the solution at the specified temperature. Stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    94. SUBTASK 70-11-48-110-094 Solution Code 172 - Aqueous Degreaser Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      25 percent by volume

      15 to 25 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with cold water to approximately 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous degreaser.

      3. Stir to mix the solution.

      4. Increase the solution temperature to the temperature specified by the cleaning process.

      5. Fill the remaining volume of the tank with tap water but make sure to keep the solution at the specified temperature. Stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    95. SUBTASK 70-11-48-110-095 Solution Code 173 - Aqueous Cleaner Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      15 percent by volume

      10 to 15 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with cold water to approximately 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous cleaner.

      3. Stir to mix the solution.

      4. Increase the solution temperature to the temperature specified by the cleaning process.

      5. Fill the remaining volume of the tank with tap water but make sure to keep the solution at the specified temperature. Stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

  96. SUBTASK 70-11-48-110-096 Solution Code 174 - Neutral Deoxidizer Solution - Deleted

    97. SUBTASK 70-11-48-110-097 Solution Code 175 - Alkaline Rust Remover Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      30 percent by volume

      20 to 30 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with cold water to approximately 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the alkaline rust remover.

      3. Stir to mix.

      4. Fill the tank with clean water to the operating volume.

      5. Stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    98. SUBTASK 70-11-48-110-098 Solution Code 176 - Wet Abrasive Solution (500 grit Aluminium Oxide) - Deleted

    1. This subtask is deleted. Refer to TASK 70-12-13-100-501

    99. SUBTASK 70-11-48-110-099 Solution Code 178 - Aqueous Cleaner Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      18 percent by volume

      13 to 18 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with tap water to approximately 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous cleaner.

      3. Stir to mix the solution.

      4. Fill the remaining volume of the tank with tap water.

      5. Stir to mix the solution.

      6. Increase the solution temperature to the temperature specified in the cleaning process.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    100. SUBTASK 70-11-48-110-100 Solution Code 179 - Aqueous Cleaner Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      20 percent by volume

      15 to 20 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with tap water to approximately 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous cleaner.

      3. Stir to mix the solution.

      4. Fill the remaining volume of the tank with tap water.

      5. Stir to mix the solution.

      6. Increase the solution temperature to the temperature specified in the cleaning process.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    101. SUBTASK 70-11-48-110-101 Solution Code 180 - Aqueous Cleaner Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      10 percent by volume

      5 to 10 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with tap water to approximately 50 percent of its operating volume.

      2. Slowly and carefully add the necessary amount of the aqueous cleaner.

      3. Stir to mix the solution.

      4. Fill the remaining volume of the tank with tap water.

      5. Stir to mix the solution.

      6. Increase the solution temperature to the temperature specified in the cleaning process.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    102. SUBTASK 70-11-48-110-102 Solution Code 181 Engine Gas Path Cleaning Solution

      1. Composition of the solution

        1. Use one of the Solution Code 181 suffixes:

        1. Solution Code 181-9A

          Material

          Make-Up

          100 percent by volume

        2. Solution Code 181-9B

          Material

          Make-Up

          15 parts by volume

          Potable water (refer to potable water quality specifications in SPM TASK 70-10-00-100-501)

          85 parts by volume

        3. Solution Code 181-10A

          Material

          Make-Up

          1 part by volume

          Potable water (refer to potable water quality specifications in SPM TASK 70-10-00-100-501)

          4 parts by volume

        4. Solution Code 181-10B

          Material

          Make-Up

          100 percent by volume

        5. Solution Code 181-11A

          Material

          Make-Up

          1 part by volume

          Potable water (refer to potable water quality specifications in SPM TASK 70-10-00-100-501)

          9 parts by volume

        6. Solution Code 181-11B

          Material

          Make-Up

          100 percent by volume

        7. Solution Code 181-11C

          Material

          Make-Up

          1 part by volume

          Potable water (refer to potable water quality specifications in SPM TASK 70-10-00-100-501)

          4 parts by volume

        8. Solution Code 181-13

          Material

          Make-Up

          1 part by volume

          Potable water (refer to potable water quality specifications in SPM TASK 70-10-00-100-501)

          4 parts by volume

        9. Solution Code 181-14

          Material

          Make-Up

          1 part by volume

          Potable water (refer to potable water quality specifications in SPM TASK 70-10-00-100-501)

          4 parts by volume

      2. Make-up of the solution

        NOTE

        It is necessary to start the compressor wash in one hour or less after the make-up of the solution is completed.

        1. Prepare 20 to 30 US gallons of wash fluid.

        1. For compressor washing fluids that composition of the solution above specifies to use at 100 percent by volume, fill the applicable gaspath/compressor cleaning cart with the necessary volume of compressor washing fluid.

        2. For compressor washing fluids that composition of the solution above specifies to mix with potable water, mix the necessary volumes of compressor washing fluid and potable water in the applicable gaspath/compressor cleaning cart. Refer to the Potable Water Quality Specifications in SPM TASK 70-10-00-100-501.

      2. If the ambient temperature is below 40 deg F (4.4 deg C), it is permitted to mix the solution with CoMat 01-124 ISOPROPYL ALCOHOL to prevent icing in accordance with the Engine Manual or Aircraft Maintenance Manual instructions.

      3. Use the solution at ambient temperature unless the compressor washing fluid manufacturer's instructions specify differently.

    103. SUBTASK 70-11-48-110-103 Solution Code 182 Water Wash Cleaning Solution - Deleted

    1. Refer to Solution Code 181.

    104. SUBTASK 70-11-48-110-104 Solution Code 183 Water Wash Cleaning Solution - Deleted

    1. Refer to Solution Code 181.

    105. SUBTASK 70-11-48-110-105 Solution Code 184 Water Wash Cleaning Solution - Deleted

    1. Refer to Solution Code 181.

    106. SUBTASK 70-11-48-110-106 Solution Code 185 Water Wash Cleaning Solution - Deleted

    1. Refer to Solution Code 181.

    107. SUBTASK 70-11-48-110-107 Solution Code 186 Water Wash Cleaning Solution - Deleted

    1. Refer to Solution Code 181.

    108. SUBTASK 70-11-48-110-108 Solution Code 187 Water Wash Cleaning Solution - Deleted

    1. Refer to Solution Code 181.

    109. SUBTASK 70-11-48-110-109 Solution Code 188 Water Wash Cleaning Solution - Deleted

    1. Refer to Solution Code 181.

    110. SUBTASK 70-11-48-110-110 Solution Code 189 Water Wash Cleaning Solution - Deleted

    1. Refer to Solution Code 181.

    111. SUBTASK 70-11-48-110-111 Solution Code 190 Turbine Airfoil Cleaner Solution

    1. Composition of the solution.

      Material

      Make-Up

      DELETED

      CoMat 01-581 TURBINE AIRFOIL CLEANER

      100 percent by volume

      DELETED

      2. Make-up of the solution.

      1. Slowly and carefully fill the tank to its operating level with the turbine airfoil cleaner.

      2. Stir to mix the solution.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

      2. Discard the solution when the solution has no more effect.

    112. SUBTASK 70-11-48-110-112 Solution Code 191 - Aqueous Carbon Remover Solution

    1. Composition of the solution.

      Material

      Make-Up

      100 percent by volume

      2. Make-up of the solution.

      1. Slowly and carefully add the necessary amount of the aqueous-based carbon remover.

      2. Increase the solution temperature to the temperature specified in the stripping process.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    113. SUBTASK 70-11-48-110-113 Solution Code 192 Alkaline Rust Remover Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      20 percent by volume

      10 to 20 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with water to 50 percent of the operating volume.

      2. Slowly and carefully add the necessary amount of the alkaline rust remover, and stir to mix.

      3. Fill the tank with water to 100 percent of its operating volume, and stir to mix.

      4. Increase the temperature of the solution to the temperature specified in the cleaning procedure. Keep the solution at the specified temperature, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    114. SUBTASK 70-11-48-110-114 Solution Code 193 - Neutral Deoxidizer Solution

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      40 percent by volume

      30 to 40 percent by volume

      2. Make-up of the solution.

      1. Fill the tank with water to 50 percent of the operating volume.

      2. Slowly and carefully add the necessary amount of the neutral deoxidizer, and stir to mix.

      3. Fill the tank with water to 100 percent of its operating volume, and stir to mix.

      4. Increase the temperature of the solution to the temperature specified in the cleaning process. Keep the solution at the specified temperature, and stir to mix.

      3. Solution maintenance.

      1. Refer to the manufacturer's instructions to do the maintenance of the solution.

    115. SUBTASK 70-11-48-110-115 Solution Code 208 - Potassium Hydroxide Solution, 45 Percent

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      3.75 lbs/gal (450g/L)

      3.5 to 4.0 lbs/gal (400 to 500 g/L)

      Specific gravity: 1.3881 - 1.5024

      2. Make-up of the solution.

      1. Fill the container to approximately 80 percent of the operating volume with water.

      2. WARNING

        CARE MUST BE TAKEN WHEN YOU ADD COMPOUNDS THAT CONTAIN SOLID SODIUM HYDROXIDE TO WATER, BECAUSE HEAT IS GIVEN OUT WHEN THE COMPOUND DISSOLVES. WHILE YOU ADD THE COMPOUND TO THE SOLUTION, THERE MUST BE STRONG MOVEMENT OF THE SOLUTION TO PREVENT HIGH CONCENTRATIONS OF THE COMPOUND IN SMALL AREAS OF THE TANK, WHICH CAN CAUSE THE SOLUTION TO BOIL.

        As you agitate the solution, slowly and carefully add the necessary quantity of CoMat 01-130A POTASSIUM HYDROXIDE KOH. Stir to dissolve.

      3. Add the remaining quantity of water. Stir to mix.

      3. Alternate Solution

      4. Solution Maintenance

      1. To do the maintenance of the solution, refer to SPM TASK 70-11-47-110-501, Subtask 70-11-47-170-012, Subtask 70-11-47-180-025 (P-55 Test Method)

    116. SUBTASK 70-11-48-110-115 Solution Code 209 - Potassium Hydroxide Solution, 27 Percent

    1. Composition of the solution.

      Material

      Make-Up

      Operating Limits

      2.25 lbs/gal (270g/L)

      2.0 to 2.5 lbs/gal (240 to 300 g/L)

      Specific gravity: 1.2210 - 1.2813

      2. Make-up of the solution.

      1. Fill the container to approximately 80 percent of the operating volume with water.

      2. WARNING

        CARE MUST BE TAKEN WHEN YOU ADD COMPOUNDS THAT CONTAIN SOLID SODIUM HYDROXIDE TO WATER, BECAUSE HEAT IS GIVEN OUT WHEN THE COMPOUND DISSOLVES. WHILE YOU ADD THE COMPOUND TO THE SOLUTION, THERE MUST BE STRONG MOVEMENT OF THE SOLUTION TO PREVENT HIGH CONCENTRATIONS OF THE COMPOUND IN SMALL AREAS OF THE TANK, WHICH CAN CAUSE THE SOLUTION TO BOIL.

        As you agitate the solution, slowly and carefully add the necessary quantity of CoMat 01-130A POTASSIUM HYDROXIDE KOH. Stir to dissolve.

      3. Add the remaining quantity of water. Stir to mix.

        5. Solution Maintenance

        1. To do the maintenance of the solution, refer to SPM TASK 70-11-47-110-501, Subtask 70-11-47-170-012, Subtask 70-11-47-180-025 (P-55 Test Method)

Requirements After Job Completion

Follow-On Conditions

NONE
Change Type:

Update CoMat information (REA20VC069)

Change Type:

Add PW potassium hydroxide solutions SPS 229-1 and SPS 229-2 and associated consumables (REA20VC128)

Change Type:

Update consumables cleaner (REA15VC312B)

Manufacturer Code:04UX7
Enterprise Name:POTTERS INDUSTRIES INC.
BU Name:POTTERS INDUSTRIES INC
Building:VALLEYBROOKE CORPORATE CENTER
Street:300 LINDENWOOD DR
City:MALVERN
State:PA
Zip Code:19355
Country:USA
Manufacturer Code:08ZP2
Enterprise Name:BASF CORPORATION
BU Name:BASF CORPORATION
Street:100 CAMPUS DRIVE
City:FLORHAM
State:NEW JERSEY
Zip Code:07932
Country:USA
Phone Number:+1-216-839-7475
Fax Number:+1-973-245-6702
Manufacturer Code:0GA37
Enterprise Name:MODERN CHEMICAL INC.
BU Name:MODERN CHEMICAL INC.
Street:7023 CENTENNIAL ROAD
P.O. Box:368
City:JACKSONVILLE
Zip Code:AR 72076
Country:USA
Phone Number:1-501-988-1311
Fax Number:1-501-988-2229
Internet:www.bluegoldcleaners.com
Manufacturer Code:0WUA8
Enterprise Name:PETROFERM INC
BU Name:PETROFERM INC
Street:2416 LYNNDALE RD
City:FERNANDINA BEACH
State:FL
Zip Code:32034
Country:USA
Phone Number:1-904-261-8286
Fax Number:1-904-261-6994
Internet:www.petroferm.com
Manufacturer Code:1EYE7
Enterprise Name:NUVITE CHEMICAL COMPOUNDS CORPORATION
BU Name:NUVITE CHEMICAL COMPOUNDS CORPORATION
Street:213 FREEMAN ST
City:BROOKLYN
State:NY
Zip Code:11222-1404
Country:USA
Phone Number:1-718-383-8351, 1-800-394-8351
Fax Number:1-718-383-0008
Email:nuvite@nuvitechemicals.com
Internet:www.nuvitechemical.com
Manufacturer Code:24853
Enterprise Name:DELETED. REFER TO VENDOR CODE 5FCA4.
Manufacturer Code:35502
Enterprise Name:MAG-CHEM INC
BU Name:MAG-CHEM INC
Street:1271 AMPERE
City:BOUCHERVILLE
State:QUEBEC
Zip Code:J4B 5Z5
Country:CANADA
Phone Number:1-450-655-1344, 1-800-363-9929
Fax Number:1-450-655-5428
Email:magnus@magchem.com
Internet:www.magchem.com
Manufacturer Code:62596
Enterprise Name:MICRO ABRASIVES CORPORATION
BU Name:MICRO ABRASIVES CORPORATION
Street:720 SOUTHAMPTON RD
P.O. Box:669
City:WESTFIELD
State:MA
Zip Code:01085-0669
Country:USA
Phone Number:1-413-562-3641
Fax Number:1-413-562-7409
Internet:www.microgrit.com
Manufacturer Code:62755
Enterprise Name:VAPOR BLAST MFG CO
BU Name:3025 W ATKINSON AVE
Street:3025 W ATKINSON AVE
City:MILWAUKEE
State:WI
Zip Code:53209-6030
Country:USA
Phone Number:1-414-871-6500
Fax Number:Fax 1-414-871-7683
Email:sales@vaporblast.com
Internet:www.vaporblast.com
Manufacturer Code:63247
Enterprise Name:MIRACHEM CORP
BU Name:UNIT 103
Street:4645 W.MCDOWELL ROAD
City:PHOENIX
State:AZ
Zip Code:85035
Country:USA
Phone Number:1-800-847-3527
Fax Number:1-602-353-1411
Email:cservice@mirachem.com
Internet:www.mirachem.com
Manufacturer Code:71410
Enterprise Name:HENKEL CORPORATION (WAS: TURCO PRODUCTS, INC)
BU Name:HENKEL CORPORATION (WAS: TURCO PRODUCTS, INC)
Street:32100 STEPHENSON HIGHWAY
City:MADISON HEIGHTS
State:MI
Zip Code:48071
Country:USA
Phone Number:1-248-583-9300
Fax Number:1-248-583-2976
Internet:www.aerospace.henkel.com
Manufacturer Code:89524
Enterprise Name:NALCO CO
BU Name:NALCO CO
Street:1601 WEST DIEHL ROAD
City:NAPERVILLE
State:ILLINOIS
Zip Code:60563-1198
Country:USA
Phone Number:1-630-305-1000, 1-630-305-1419, 1-877-813-3523
Fax Number:1-630-305-2900
Internet:www.nalco.com
Manufacturer Code:8B756
Enterprise Name:MALVERN MINERALS CO
BU Name:MALVERN MINERALS CO
P.O. Box:1238
City:HOT SPRINGS NATIONAL PARK
Zip Code:AR 71902-1246
Country:USA
Phone Number:1-501-623-8893
Fax Number:1-501-623-5113
Email:novacite@hsnp.com
Manufacturer Code:94058
Enterprise Name:BRULIN CORP
BU Name:BRULIN CORP
Street:2920 DR ANDREW J BROWN
City:DRIVE
Zip Code:IN 46206
Country:USA
Phone Number:1-317-923-3211, 1-800-776-7149
Fax Number:1�317�925�4596
Manufacturer Code:IAE63
Enterprise Name:MODERN CHEMICAL INC
BU Name:MODERN CHEMICAL INC
City:SEE CAGE CODE 0GA37
Country:SEE CAGE CODE 0GA37
Manufacturer Code:IE531
Enterprise Name:DELETED
BU Name:DELETED. WAS TREIBACHER SCHLEIFMITTEL NORTH AMERICA. REFER TO VENDOR CODE V531V.
Manufacturer Code:K4754
Enterprise Name:SOCOMOR LTD
BU Name:SOCOMOR LTD
Street:6 MERLEWOOD,BRACKNELL
City:BERKSHIRE
Zip Code:RG12 9PA
Country:ENGLAND
Phone Number:44-1344-860647
Fax Number:44-1344-860652
Email:uk@socomor.com
Internet:www.socomor.com
Manufacturer Code:LOCAL
Enterprise Name:LOCALLY SUPPLIED
Manufacturer Code:Z0142
Enterprise Name:APPLIED CHEMICALS PTY LTD
BU Name:APPLIED CHEMICALS PTY LTD
Street:90-92 FAIRBANK ROAD
City:CLAYTON SOUTH,VICTORIA
Zip Code:3169
Country:AUSTRALIA
Phone Number:61-(3)-8542-5111
Fax Number:61-(3)-8542-5188
Email:applied.aus@appliedchemicals.com
Internet:www.apchem.com.au
Manufacturer Code:LOCAL
Supply Number:CoMat 01-022
Type:sp01
Supply Short Name:CoMat 01-022 SODIUM HYDROXIDE NaOH (SOLID)
Supply Name:CoMat 01-022 SODIUM HYDROXIDE NaOH (SOLID)
Specification Groups:
Doc NumberType
ASTM D 456 CAUSTIC SODA, PEARLS OR FLAKES
Suppliers:
ManufacturerRemarks
LOCAL
K6835
U0SV8
Manufacturer Code:5FCA4
Supply Number:CoMat 01-025
Type:sp01
Supply Short Name:CoMat 01-025 NITRIC ACID HNO3, TECHNICAL GRADE
Supply Name:CoMat 01-025 NITRIC ACID HNO3, TECHNICAL GRADE
Specification Groups:
Doc NumberType
orTECHNICAL GRADE SP.GR. 1.42 NITRIC ACID
orTECHNICAL GRADE 42 BAUME NITRIC ACID
TECHNICAL GRADE 67.5 WT% NITRIC ACID
Suppliers:
ManufacturerRemarks
5FCA4
K6835
LOCAL
U0PR4
U0SV8
U6726
V272V
Manufacturer Code:LOCAL
Supply Number:CoMat 01-055
Type:sp01
Supply Short Name:CoMat 01-055 POTASSIUM PERMANGANATE KMnO4
Supply Name:CoMat 01-055 POTASSIUM PERMANGANATE KMnO4
Specification Groups:
Doc NumberType
POTASSIUM PERMANGANATE, COMMERCIAL GRADE
JCR-013 (JAEC REF)POTASSIUM PERMANGANATE, COMMERCIAL GRADE
MTH 166 (98%) (MTU REF)POTASSIUM PERMANGANATE, COMMERCIAL GRADE
Suppliers:
ManufacturerRemarks
LOCAL
U1185
K6835
Manufacturer Code:LOCAL
Supply Number:CoMat 01-072
Type:sp01
Supply Short Name:CoMat 01-072 PRIMARY CLEANER
Supply Name:CoMat 01-072 PRIMARY CLEANER
Specification Groups:
Doc NumberType
OMAT:1/24D (RR REF)ARDROX 6376
JCR-008 (JAEC REF)ARDROX 6376
SPMC 207 (PW REF)ARDROX 6376
Suppliers:
ManufacturerRemarks
LOCAL
37127
B1082
D1940
IE206
K6835
K6858
0L040
Z1363
23373
Manufacturer Code:LOCAL
Supply Number:CoMat 01-124
Type:sp01
Supply Short Name:CoMat 01-124 ISOPROPYL ALCOHOL
Supply Name:CoMat 01-124 ISOPROPYL ALCOHOL
Specification Groups:
Doc NumberType
OMAT:1/40GPR TECHNICAL GRADE
PMC 9094GPR TECHNICAL GRADE
JCR-011GPR TECHNICAL GRADE
Suppliers:
ManufacturerRemarks
LOCAL
U1185
24853
K6835
Manufacturer Code:24853
Supply Number:CoMat 01-130A
Type:sp01
Supply Short Name:CoMat 01-130A POTASSIUM HYDROXIDE KOH
Supply Name:CoMat 01-130A POTASSIUM HYDROXIDE KOH
Specification Groups:
Doc NumberType
PMC 1606-1COMMERCIAL GRADE S.G 2.044
Suppliers:
ManufacturerRemarks
24853
LOCAL
Manufacturer Code:LOCAL
Supply Number:CoMat 01-188
Type:sp01
Supply Short Name:CoMat 01-188 ALKALINE RUST REMOVER (LIQUID)
Supply Name:CoMat 01-188 ALKALINE RUST REMOVER (LIQUID)
Specification Groups:
Doc NumberType
SPMC 91 (PW REF)CEE-BEE J-84AL
Suppliers:
ManufacturerRemarks
LOCAL
3MCT7
U5702
Manufacturer Code:8B756
Supply Number:CoMat 01-202
Type:sp01
Supply Short Name:CoMat 01-202 WET ABRASIVE COMPOUND
Supply Name:CoMat 01-202 WET ABRASIVE COMPOUND
Specification Groups:
Doc NumberType
PMC 3067 (PW REF)NO. 325 NOVACITE
Suppliers:
ManufacturerRemarks
8B756
Manufacturer Code:8B756
Supply Number:CoMat 01-204
Type:sp01
Supply Short Name:CoMat 01-204 WET ABRASIVE COMPOUND
Supply Name:CoMat 01-204 WET ABRASIVE COMPOUND
Specification Groups:
Doc NumberType
PMC 3085 (PW REF)NO. 200 NOVACITE
Suppliers:
ManufacturerRemarks
8B756
Manufacturer Code:62755
Supply Number:CoMat 01-207
Type:sp01
Supply Short Name:CoMat 01-207 ANTISOLIDIFYING COMPOUND
Supply Name:CoMat 01-207 ANTISOLIDIFYING COMPOUND
Specification Groups:
Doc NumberType
PMC 1612NO-PAK
Suppliers:
ManufacturerRemarks
62755
Manufacturer Code:LOCAL
Supply Number:CoMat 01-230C
Type:sp01
Supply Short Name:CoMat 01-230C COMPRESSOR WASHING FLUID
Supply Name:CoMat 01-230C COMPRESSOR WASHING FLUID
Specification Groups:
Doc NumberType
SPMC 87-10A (PW REF)ARDROX 6367
Suppliers:
ManufacturerRemarks
LOCAL
0L040
23373
37127
D1940
IE206
K6858
Manufacturer Code:LOCAL
Supply Number:CoMat 01-230D
Type:sp01
Supply Short Name:CoMat 01-230D COMPRESSOR WASHING FLUID
Supply Name:CoMat 01-230D COMPRESSOR WASHING FLUID
Specification Groups:
Doc NumberType
ZOK 27SPMC 87-13 (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
IE546
Manufacturer Code:LOCAL
Supply Number:CoMat 01-230E
Type:sp01
Supply Short Name:CoMat 01-230E COMPRESSOR WASHING FLUID
Supply Name:CoMat 01-230E COMPRESSOR WASHING FLUID
Specification Groups:
Doc NumberType
SPMC 87-14 (PW REF)TURBO-K
Suppliers:
ManufacturerRemarks
LOCAL
IE546
Manufacturer Code:LOCAL
Supply Number:CoMat 01-230F
Type:sp01
Supply Short Name:CoMat 01-230F COMPRESSOR WASHING FLUID
Supply Name:CoMat 01-230F COMPRESSOR WASHING FLUID
Specification Groups:
Doc NumberType
ARDROX 6368SPMC 87-10B (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
D1940
0L040
23373
37127
IE206
K6858
Manufacturer Code:LOCAL
Supply Number:CoMat 01-230G
Type:sp01
Supply Short Name:CoMat 01-230G COMPRESSOR WASHING FLUID
Supply Name:CoMat 01-230G COMPRESSOR WASHING FLUID
Specification Groups:
Doc NumberType
TURCO 6783-3SPMC 87-11A (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
71410
Manufacturer Code:LOCAL
Supply Number:CoMat 01-230H
Type:sp01
Supply Short Name:CoMat 01-230H COMPRESSOR WASHING FLUID
Supply Name:CoMat 01-230H COMPRESSOR WASHING FLUID
Specification Groups:
Doc NumberType
TURCO 6783-10SPMC 87-11B (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
71410
Manufacturer Code:LOCAL
Supply Number:CoMat 01-230J
Type:sp01
Supply Short Name:CoMat 01-230J COMPRESSOR WASHING FLUID
Supply Name:CoMat 01-230J COMPRESSOR WASHING FLUID
Specification Groups:
Doc NumberType
TURCO 6783-50SPMC 87-11C (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
71410
Manufacturer Code:LOCAL
Supply Number:CoMat 01-230K
Type:sp01
Supply Short Name:CoMat 01-230K COMPRESSOR WASHING FLUID
Supply Name:CoMat 01-230K COMPRESSOR WASHING FLUID
Specification Groups:
Doc NumberType
ECT R-MC PART NO. 4070SPMC 87-9A (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
IE550
Manufacturer Code:LOCAL
Supply Number:CoMat 01-230L
Type:sp01
Supply Short Name:CoMat 01-230L COMPRESSOR WASHING FLUID
Supply Name:CoMat 01-230L COMPRESSOR WASHING FLUID
Specification Groups:
Doc NumberType
ECT R-MC PART NO. 4072SPMC 87-9B (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
IE550
Manufacturer Code:LOCAL
Supply Number:CoMat 01-265
Type:sp01
Supply Short Name:CoMat 01-265 ADDITIVE
Supply Name:CoMat 01-265 ADDITIVE
Specification Groups:
Doc NumberType
SPMC 2-2 (PW REF)CEE-BEE GO-2L
Suppliers:
ManufacturerRemarks
LOCAL
3MCT7
U5702
Manufacturer Code:0GA37
Supply Number:CoMat 01-300
Type:sp01
Supply Short Name:CoMat 01-300 ALKALI CLEANER (GENERAL PURPOSE)
Supply Name:CoMat 01-300 ALKALI CLEANER (GENERAL PURPOSE)
Specification Groups:
Doc NumberType
PMC 1284 (PW REF)BLUE GOLD INDUSTR. CLEANER
Suppliers:
ManufacturerRemarks
0GA37
Manufacturer Code:LOCAL
Supply Number:CoMat 01-327
Type:sp01
Supply Short Name:CoMat 01-327 NITRIC ACID
Supply Name:CoMat 01-327 NITRIC ACID
Specification Groups:
Doc NumberType
PMC 1019REAGENT GRADE (68 - 70% BY WEIGHT)
Suppliers:
ManufacturerRemarks
LOCAL
Manufacturer Code:LOCAL
Supply Number:CoMat 01-339
Type:sp01
Supply Short Name:CoMat 01-339 ALKALI CLEANER (GENERAL PURPOSE)
Supply Name:CoMat 01-339 ALKALI CLEANER (GENERAL PURPOSE)
Specification Groups:
Doc NumberType
CEE-BEE A-7X7SPMC 104 (PW REF)
SPMC 104CEE-BEE A-7X7
Suppliers:
ManufacturerRemarks
LOCAL
3MCT7
U5702
Manufacturer Code:LOCAL
Supply Number:CoMat 01-340
Type:sp01
Supply Short Name:CoMat 01-340 ALKALI CLEANER (GENERAL PURPOSE)
Supply Name:CoMat 01-340 ALKALI CLEANER (GENERAL PURPOSE)
Specification Groups:
Doc NumberType
SPMC 105 (PW REF)TURCO 5948 DPM
Suppliers:
ManufacturerRemarks
LOCAL
71410
IE386
Manufacturer Code:LOCAL
Supply Number:CoMat 01-368
Type:sp01
Supply Short Name:CoMat 01-368 ALKALINE RUST REMOVER
Supply Name:CoMat 01-368 ALKALINE RUST REMOVER
Specification Groups:
Doc NumberType
SPMC 115 (PW REF)ARDROX 185L
Suppliers:
ManufacturerRemarks
LOCAL
0L040
23373
37127
D1940
IE206
K6858
Manufacturer Code:71410
Supply Number:CoMat 01-369
Type:sp01
Supply Short Name:CoMat 01-369 ALKALINE RUST REMOVER
Supply Name:CoMat 01-369 ALKALINE RUST REMOVER
Specification Groups:
Doc NumberType
SPMC 116 (PW REF)TURCO 4181L
Suppliers:
ManufacturerRemarks
71410
Manufacturer Code:K4754
Supply Number:CoMat 01-417
Type:sp01
Supply Short Name:CoMat 01-417 ALKALINE RUST REMOVER (LIQUID)
Supply Name:CoMat 01-417 ALKALINE RUST REMOVER (LIQUID)
Specification Groups:
Doc NumberType
SPMC 129 (PW REF)MAG-CHEM HDL-202
Suppliers:
ManufacturerRemarks
K4754
LOCAL
02ER0
Manufacturer Code:LOCAL
Supply Number:CoMat 01-418
Type:sp01
Supply Short Name:CoMat 01-418 ADDITIVE, ALKALINE RUST REMOVER
Supply Name:CoMat 01-418 ADDITIVE, ALKALINE RUST REMOVER
Specification Groups:
Doc NumberType
SPMC 129-1 (PW REF)MAG-CHEM DEOX
Suppliers:
ManufacturerRemarks
LOCAL
02ER0
K4754
Manufacturer Code:IAE63
Supply Number:CoMat 01-421
Type:sp01
Supply Short Name:CoMat 01-421 CLEANER, ALKALI (GENERAL PURPOSE, LOW FOAM)
Supply Name:CoMat 01-421 CLEANER, ALKALI (GENERAL PURPOSE, LOW FOAM)
Specification Groups:
Doc NumberType
SPMC 106 (PW REF)BLUE GOLD SPRAY WASH (LOW FOAM)
Suppliers:
ManufacturerRemarks
IAE63
Manufacturer Code:LOCAL
Supply Number:CoMat 01-426
Type:sp01
Supply Short Name:CoMat 01-426 ACIDIC SCALE CONDITIONER
Supply Name:CoMat 01-426 ACIDIC SCALE CONDITIONER
Specification Groups:
Doc NumberType
SPMC 8 (PW REF)CEE-BEE J-3
Suppliers:
ManufacturerRemarks
LOCAL
3MCT7
U5702
Manufacturer Code:LOCAL
Supply Number:CoMat 01-443
Type:sp01
Supply Short Name:CoMat 01-443 ALKALINE PERMANGANATE (LIQUID)
Supply Name:CoMat 01-443 ALKALINE PERMANGANATE (LIQUID)
Specification Groups:
Doc NumberType
SPMC 114 (PW REF)ARDROX 188 RFU
Suppliers:
ManufacturerRemarks
LOCAL
0L040
23373
D1940
K6858
37127
Manufacturer Code:LOCAL
Supply Number:CoMat 01-444
Type:sp01
Supply Short Name:CoMat 01-444 ADDITIVE (CAUSTIC), ALKALINE PERMANGANATE
Supply Name:CoMat 01-444 ADDITIVE (CAUSTIC), ALKALINE PERMANGANATE
Specification Groups:
Doc NumberType
SPMC 114-1 (PW REF)ARDROX 188 LC
Suppliers:
ManufacturerRemarks
LOCAL
0L040
23373
D1940
K6858
37127
IE206
Manufacturer Code:LOCAL
Supply Number:CoMat 01-445
Type:sp01
Supply Short Name:CoMat 01-445 ADDITIVE (PERMANGANATE), ALKALINE PERMANGANATE
Supply Name:CoMat 01-445 ADDITIVE (PERMANGANATE), ALKALINE PERMANGANATE
Specification Groups:
Doc NumberType
SPMC 114-2 (PW REF)ARDROX 188 LP
Suppliers:
ManufacturerRemarks
LOCAL
0L040
23373
D1940
K6858
37127
IE206
Manufacturer Code:71410
Supply Number:CoMat 01-446
Type:sp01
Supply Short Name:CoMat 01-446 ACIDIC SCALE CONDITIONER
Supply Name:CoMat 01-446 ACIDIC SCALE CONDITIONER
Specification Groups:
Doc NumberType
SPMC 130SCALE GON No5
Suppliers:
ManufacturerRemarks
71410
Manufacturer Code:LOCAL
Supply Number:CoMat 01-468
Type:sp01
Supply Short Name:CoMat 01-468 AQUEOUS CLEANER (LOW FOAM)
Supply Name:CoMat 01-468 AQUEOUS CLEANER (LOW FOAM)
Specification Groups:
Doc NumberType
SPMC 113 (PW REF)MAG-CHEM DG KLEEN
Suppliers:
ManufacturerRemarks
LOCAL
02ER0
K4754
Manufacturer Code:1EYE7
Supply Number:CoMat 01-469
Type:sp01
Supply Short Name:CoMat 01-469 AQUEOUS DEGREASER
Supply Name:CoMat 01-469 AQUEOUS DEGREASER
Specification Groups:
Doc NumberType
SPMC 151 (PW REF)NU-GEAR-SC
Suppliers:
ManufacturerRemarks
1EYE7
Manufacturer Code:LOCAL
Supply Number:CoMat 01-474
Type:sp01
Supply Short Name:CoMat 01-474 PHOSPHORIC ACID, INHIBITED
Supply Name:CoMat 01-474 PHOSPHORIC ACID, INHIBITED
Specification Groups:
Doc NumberType
SPMC 21 (PW REF)ARDROX 1218
Suppliers:
ManufacturerRemarks
LOCAL
23373
0L040
37127
D1940
IE206
K6858
Manufacturer Code:LOCAL
Supply Number:CoMat 01-478
Type:sp01
Supply Short Name:CoMat 01-478 ACIDIC SCALE CONDITIONER
Supply Name:CoMat 01-478 ACIDIC SCALE CONDITIONER
Specification Groups:
Doc NumberType
SPMC 191 (PW REF)ARDROX 1873A
Suppliers:
ManufacturerRemarks
LOCAL
D1940
K6858
0L040
23373
IE206
37127
Manufacturer Code:LOCAL
Supply Number:CoMat 01-479
Type:sp01
Supply Short Name:CoMat 01-479 AQUEOUS DEGREASER
Supply Name:CoMat 01-479 AQUEOUS DEGREASER
Specification Groups:
Doc NumberType
SPMC 171 (PW REF)TURCO SPRAYEZE NP LT
Suppliers:
ManufacturerRemarks
LOCAL
71410
Manufacturer Code:LOCAL
Supply Number:CoMat 01-480
Type:sp01
Supply Short Name:CoMat 01-480 AQUEOUS DEGREASER
Supply Name:CoMat 01-480 AQUEOUS DEGREASER
Specification Groups:
Doc NumberType
SPMC 181 (PW REF)CEE-BEE SUPER BEE 300 LF
Suppliers:
ManufacturerRemarks
LOCAL
3MCT7
U5702
Manufacturer Code:63247
Supply Number:CoMat 01-481
Type:sp01
Supply Short Name:CoMat 01-481 AQUEOUS DEGREASER
Supply Name:CoMat 01-481 AQUEOUS DEGREASER
Specification Groups:
Doc NumberType
SPMC 196 (PW REF)MIRACHEM 750
Suppliers:
ManufacturerRemarks
63247
Manufacturer Code:LOCAL
Supply Number:CoMat 01-483
Type:sp01
Supply Short Name:CoMat 01-483 AQUEOUS DEGREASER
Supply Name:CoMat 01-483 AQUEOUS DEGREASER
Specification Groups:
Doc NumberType
SPMC 170 (PW REF)ARDROX 6333A
Suppliers:
ManufacturerRemarks
LOCAL
D1940
K6858
0L040
23373
IE206
37127
Manufacturer Code:LOCAL
Supply Number:CoMat 01-486
Type:sp01
Supply Short Name:CoMat 01-486 AQUEOUS DEGREASER
Supply Name:CoMat 01-486 AQUEOUS DEGREASER
Specification Groups:
Doc NumberType
SPMC 178 (PW REF)MAG-CHEM SOLUWAX
Suppliers:
ManufacturerRemarks
LOCAL
02ER0
K4754
Manufacturer Code:94058
Supply Number:CoMat 01-487
Type:sp01
Supply Short Name:CoMat 01-487 AQUEOUS DEGREASER
Supply Name:CoMat 01-487 AQUEOUS DEGREASER
Specification Groups:
Doc NumberType
SPMC 184 (PW REF)BRULIN 815 GD
Suppliers:
ManufacturerRemarks
94058
Manufacturer Code:63247
Supply Number:CoMat 01-488
Type:sp01
Supply Short Name:CoMat 01-488 AQUEOUS DEGREASER
Supply Name:CoMat 01-488 AQUEOUS DEGREASER
Specification Groups:
Doc NumberType
SPMC 195 (PW REF)MIRACHEM 500
Suppliers:
ManufacturerRemarks
63247
Manufacturer Code:LOCAL
Supply Number:CoMat 01-501
Type:sp01
Supply Short Name:CoMat 01-501 CORROSION INHIBITOR (WATER SOLUBLE)
Supply Name:CoMat 01-501 CORROSION INHIBITOR (WATER SOLUBLE)
Specification Groups:
Doc NumberType
SPMC 194 (PW REF)ARDROX 3705
Suppliers:
ManufacturerRemarks
LOCAL
D1940
K6858
0L040
23373
IE206
37127
Manufacturer Code:LOCAL
Supply Number:CoMat 01-502
Type:sp01
Supply Short Name:CoMat 01-502 CORROSION INHIBITOR (WATER SOLUBLE)
Supply Name:CoMat 01-502 CORROSION INHIBITOR (WATER SOLUBLE)
Specification Groups:
Doc NumberType
SPMC 172 (PW REF)CEE-BEE NORTEX 3025
Suppliers:
ManufacturerRemarks
LOCAL
3MCT7
U5702
Manufacturer Code:LOCAL
Supply Number:CoMat 01-503A
Type:sp01
Supply Short Name:CoMat 01-503A ALKALINE PERMANGANATE, PART 1
Supply Name:CoMat 01-503A ALKALINE PERMANGANATE, PART 1
Specification Groups:
Doc NumberType
TURCO 4338-L PART1SPMC 15-1 (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
71410
Manufacturer Code:LOCAL
Supply Number:CoMat 01-503B
Type:sp01
Supply Short Name:CoMat 01-503B ALKALINE PERMANGANATE, PART 2
Supply Name:CoMat 01-503B ALKALINE PERMANGANATE, PART 2
Specification Groups:
Doc NumberType
TURCO 4338-L PART2SPMC 15-2 (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
71410
Manufacturer Code:Z0142
Supply Number:CoMat 01-509
Type:sp01
Supply Short Name:CoMat 01-509 AQUEOUS DEGREASER
Supply Name:CoMat 01-509 AQUEOUS DEGREASER
Specification Groups:
Doc NumberType
SPMC 138Applied 4204
Suppliers:
ManufacturerRemarks
Z0142
Manufacturer Code:89524
Supply Number:CoMat 01-540
Type:sp01
Supply Short Name:CoMat 01-540 AQUEOUS CLEANER
Supply Name:CoMat 01-540 AQUEOUS CLEANER
Specification Groups:
Doc NumberType
SPMC 208 (PW REF)CRP-240
Suppliers:
ManufacturerRemarks
89524
Manufacturer Code:LOCAL
Supply Number:CoMat 01-541A
Type:sp01
Supply Short Name:CoMat 01-541A ADDITIVE (ALKALINE PERMANGATE)
Supply Name:CoMat 01-541A ADDITIVE (ALKALINE PERMANGATE)
Specification Groups:
Doc NumberType
SPMC 16-1 (PW REF)CEE-BEE J-88 ADDITIVE PL
Suppliers:
ManufacturerRemarks
LOCAL
Manufacturer Code:LOCAL
Supply Number:CoMat 01-541B
Type:sp01
Supply Short Name:CoMat 01-541B ALKALINE PERMANGATE LIQUID
Supply Name:CoMat 01-541B ALKALINE PERMANGATE LIQUID
Specification Groups:
Doc NumberType
CEE-BEE J-88LSPMC 16 (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
3MCT7
Manufacturer Code:LOCAL
Supply Number:CoMat 01-542
Type:sp01
Supply Short Name:CoMat 01-542 ACID SCALE CONDITIONER
Supply Name:CoMat 01-542 ACID SCALE CONDITIONER
Specification Groups:
Doc NumberType
SPMC 154 (PW REF)MAG CHEM AP-988
Suppliers:
ManufacturerRemarks
LOCAL
02ER0
K4754
F6892
Manufacturer Code:LOCAL
Supply Number:CoMat 01-546A
Type:sp01
Supply Short Name:CoMat 01-546A ALKALINE PERMANGANATE, LIQUID, CAUSTIC COMPONENT
Supply Name:CoMat 01-546A ALKALINE PERMANGANATE, LIQUID, CAUSTIC COMPONENT
Specification Groups:
Doc NumberType
MAG-CHEM HDL 2524CSPMC 204-1 (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
02ER0
K4754
F6892
Manufacturer Code:LOCAL
Supply Number:CoMat 01-546B
Type:sp01
Supply Short Name:CoMat 01-546B ALKALINE PERMANGANATE, LIQUID, PERMANGANATE CONCENTRATE COMPONENT
Supply Name:CoMat 01-546B ALKALINE PERMANGANATE, LIQUID, PERMANGANATE CONCENTRATE COMPONENT
Specification Groups:
Doc NumberType
MAG-CHEM HDL 2524PSPMC 204-2 (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
35502
02ER0
K4754
F6892
Manufacturer Code:LOCAL
Supply Number:CoMat 01-558A
Type:sp01
Supply Short Name:CoMat 01-558A ALKALINE PERMANGANATE, LIQUID, CAUSTIC COMPONENT
Supply Name:CoMat 01-558A ALKALINE PERMANGANATE, LIQUID, CAUSTIC COMPONENT
Specification Groups:
Doc NumberType
ARDROX 1435ASPMC 203-1 (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
D1940
IE206
K6858
23373
0L040
37127
Manufacturer Code:LOCAL
Supply Number:CoMat 01-558B
Type:sp01
Supply Short Name:CoMat 01-558B ALKALINE PERMANGANATE, LIQUID, PERMANGANATE COMPONENT
Supply Name:CoMat 01-558B ALKALINE PERMANGANATE, LIQUID, PERMANGANATE COMPONENT
Specification Groups:
Doc NumberType
ARDROX 1435BSPMC 203-2 (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
D1940
IE206
K6858
0L040
23373
37127
Manufacturer Code:LOCAL
Supply Number:CoMat 01-564
Type:sp01
Supply Short Name:CoMat 01-564 AQUEOUS DEGREASER
Supply Name:CoMat 01-564 AQUEOUS DEGREASER
Specification Groups:
Doc NumberType
SPMC 173 (PW REF)CEE-BEE SUPER BEE 300 LFG
Suppliers:
ManufacturerRemarks
LOCAL
3MCT7
U5702
Manufacturer Code:0WUA8
Supply Number:CoMat 01-565
Type:sp01
Supply Short Name:CoMat 01-565 AQUEOUS CLEANER
Supply Name:CoMat 01-565 AQUEOUS CLEANER
Specification Groups:
Doc NumberType
SPMC 190 (PW REF)CLEANSAFE 787C
Suppliers:
ManufacturerRemarks
0WUA8
Manufacturer Code:LOCAL
Supply Number:CoMat 01-571
Type:sp01
Supply Short Name:CoMat 01-571 ALKALINE RUST REMOVER
Supply Name:CoMat 01-571 ALKALINE RUST REMOVER
Specification Groups:
Doc NumberType
SPMC 57 (PW REF)ARDROX 1618
Suppliers:
ManufacturerRemarks
LOCAL
D1940
K6858
0L040
23373
IE206
37127
Manufacturer Code:LOCAL
Supply Number:CoMat 01-572
Type:sp01
Supply Short Name:CoMat 01-572 SODIUM HYDROXIDE NaOH (LIQUID)
Supply Name:CoMat 01-572 SODIUM HYDROXIDE NaOH (LIQUID)
Specification Groups:
Doc NumberType
50% AQUEOUS SOLUTION OF COMMERCIAL GRADE SODIUM HYDROXIDE (49 TO 52 WEIGHT PERCENT NaOH)
Suppliers:
ManufacturerRemarks
LOCAL
Manufacturer Code:LOCAL
Supply Number:CoMat 01-575
Type:sp01
Supply Short Name:CoMat 01-575 AQUEOUS CLEANER
Supply Name:CoMat 01-575 AQUEOUS CLEANER
Specification Groups:
Doc NumberType
SPMC 237 (PW Ref)Daraclean 282GF
Suppliers:
ManufacturerRemarks
LOCAL
37676
Manufacturer Code:94058
Supply Number:CoMat 01-577
Type:sp01
Supply Short Name:
Supply Name:CoMat 01-577 AQUEOUS CLEANER
Specification Groups:
Doc NumberType
AquaVantage 3887 GDSPMC 233 (PW Ref)
Suppliers:
ManufacturerRemarks
94058
Manufacturer Code:08ZP2
Supply Number:CoMat 01-581
Type:sp01
Supply Short Name:CoMat 01-581 TURBINE AIRFOIL CLEANER
Supply Name:CoMat 01-581 TURBINE AIRFOIL CLEANER
Specification Groups:
Doc NumberType
TRILON B LIQUID CHELATING AGENT
Suppliers:
ManufacturerRemarks
08ZP2
Manufacturer Code:71410
Supply Number:CoMat 01-582
Type:sp01
Supply Short Name:CoMat 01-582 AQUEOUS-BASED CARBON REMOVER
Supply Name:CoMat 01-582 AQUEOUS-BASED CARBON REMOVER
Specification Groups:
Doc NumberType
Turco 9045-6SPMC 183-1 (PW REF)
Suppliers:
ManufacturerRemarks
71410
Manufacturer Code:LOCAL
Supply Number:CoMat 01-583
Type:sp01
Supply Short Name:CoMat 01-583 ALKALINE RUST REMOVER (LIQUID)
Supply Name:CoMat 01-583 ALKALINE RUST REMOVER (LIQUID)
Specification Groups:
Doc NumberType
TURCO 4181-GLSPMC 122 (PW REF)
Suppliers:
ManufacturerRemarks
LOCAL
71410
Manufacturer Code:35502
Supply Number:CoMat 01-584
Type:sp01
Supply Short Name:
Supply Name:CoMat 01-584 DEOXIDIZER, NEUTRAL
Specification Groups:
Doc NumberType
SPMC 244 (PW REF)MAG-CHEM HDL-73W
Suppliers:
ManufacturerRemarks
35502
Manufacturer Code:LOCAL
Supply Number:CoMat 01-589
Type:sp01
Supply Short Name:CoMat 01-589 POTASSIUM HYDROXIDE, LIQUID, 44-46%
Supply Name:CoMat 01-589 POTASSIUM HYDROXIDE, LIQUID, 44-46%
Specification Groups:
Doc NumberType
POTASSIUM HYDROXIDE LIQUID, MERCURY CELL GRADE, 44-46% POTASSIUM HYDROXIDE, BALANCE WATER, 50 PPM MAXIMUM POTASSIUM CHLORIDE
Suppliers:
ManufacturerRemarks
LOCAL
Manufacturer Code:LOCAL
Supply Number:CoMat 01-590
Type:sp01
Supply Short Name:CoMat 01-590 POTASSIUM HYDROXIDE, LIQUID, 26-28 WEIGHT PERCENT
Supply Name:CoMat 01-590 POTASSIUM HYDROXIDE, LIQUID, 26-28 WEIGHT PERCENT
Specification Groups:
Doc NumberType
POTASSIUM HYDROXIDE LIQUID, MERCURY CELL GRADE, 26-28 WEIGHT PERCENT POTASSIUM HYDROXIDE, 50 PPM MAXIMUM POTASSIUM CHLORIDE
Suppliers:
ManufacturerRemarks
LOCAL
Manufacturer Code:62596
Supply Number:CoMat 05-022
Type:sp01
Supply Short Name:CoMat 05-022 ALUMINUM OXIDE ABRASIVE
Supply Name:CoMat 05-022 ALUMINUM OXIDE ABRASIVE
Specification Groups:
Doc NumberType
PMC 3046ALUMINUM OXIDE No. 240
Suppliers:
ManufacturerRemarks
62596
Manufacturer Code:04UX7
Supply Number:CoMat 05-166
Type:sp01
Supply Short Name:CoMat 05-166 GLASS BEAD
Supply Name:CoMat 05-166 GLASS BEAD
Specification Groups:
Doc NumberType
PMC 3084BALLOTINI IMPACT BEADS
Suppliers:
ManufacturerRemarks
04UX7
Manufacturer Code:1280N
Supply Number:CoMat 05-198
Type:sp01
Supply Short Name:CoMat 05-198 ALUMINUM OXIDE, 320-GRIT
Supply Name:CoMat 05-198 ALUMINUM OXIDE, 320-GRIT
Specification Groups:
Doc NumberType
ALODUR LIONITE GF BROWN, ANSI B74.12 320-GRIT
Suppliers:
ManufacturerRemarks
1280N
Manufacturer Code:1280N
Supply Number:CoMat 05-199
Type:sp01
Supply Short Name:CoMat 05-199 ALUMINUM OXIDE, F500 GRIT
Supply Name:CoMat 05-199 ALUMINUM OXIDE, F500 GRIT
Specification Groups:
Doc NumberType
ALODUR LIONITE GF BROWN, FEPA F500 GRIT
Suppliers:
ManufacturerRemarks
1280N
Manufacturer Code:LOCAL
Supply Number:CoMat 10-097
Type:sp01
Supply Short Name:CoMat 10-097 CORROSION INHIBITOR,(NON-NITRITE)
Supply Name:CoMat 10-097 CORROSION INHIBITOR,(NON-NITRITE)
Specification Groups:
Doc NumberType
PMC 9CoMat 100INTEX 8228
Suppliers:
ManufacturerRemarks
LOCAL
D1940
K6858
0L040
23373
Manufacturer Code:71410
Supply Number:CoMat 10-099
Type:sp01
Supply Short Name:CoMat 10-099 CORROSION INHIBITOR,WATER SOLUBLE
Supply Name:CoMat 10-099 CORROSION INHIBITOR,WATER SOLUBLE
Specification Groups:
Doc NumberType
SPMC 140TURCO RUST BLOC
Suppliers:
ManufacturerRemarks
71410
Manufacturer Code:35502
Supply Number:CoMat 10-134
Type:sp01
Supply Short Name:CoMat 10-134 CORROSION INHIBITOR,(NON-NITRITE)
Supply Name:CoMat 10-134 CORROSION INHIBITOR,(NON-NITRITE)
Specification Groups:
Doc NumberType
PMC 9132CORROTEK
Suppliers:
ManufacturerRemarks
35502
Manufacturer Code:71410
Supply Number:CoMat 10-135
Type:sp01
Supply Short Name:CoMat 10-135 CORROSION INHIBITOR
Supply Name:CoMat 10-135 CORROSION INHIBITOR
Specification Groups:
Doc NumberType
SPMC 140TURCO RUST BLOC
Suppliers:
ManufacturerRemarks
71410