Export Control
EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.Copyright
© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).Applicability
All
Common Information
TASK 71-51-42-300-001 EEC Fan Harness And Ignition Supply Harness - Replace The Cables, Repair-001 (VRS2964)
Effectivity
FIG/ITEM | PART NO. |
|---|---|
01-005 | 740-5870-501 |
01-005 | 740-5870-503 |
01-005 | 740-5870-511 |
01-005 | 740-5870-513 |
01-005 | 745-5870-501 |
01-005 | 740-5870-9003 |
01-005 | 740-5870-9005 |
01-005 | 740-5870-9007 |
01-005 | 740-5870-9011 |
01-005 | 740-5870-9013 |
01-005 | 745-5870-503 |
General
The harness must be disassembled only as necessary to get access to the damaged cables.
Related repairs
Replacement of the Contact Pins and Sockets, refer to Repair, VRS2987 TASK 71-51-42-300-004 (REPAIR-004).
Replacement of the Ties, refer to Repair, VRS2972 TASK 71-51-42-300-002 (REPAIR-002).
Replacement of the Connectors, refer to Repair, VRS2980 TASK 71-51-42-300-003 (REPAIR-003).
Replacement of the Identification Sleeves, refer to Repair, VRS7002 SPM TASK 70-35-25-300-001-F01 (REPAIR-001).
Preliminary Requirements
Pre-Conditions
NONESupport Equipment
NONEConsumables, Materials and Expendables
| Name | Manufacturer | Part Number / Identification | Quantity | Remark |
|---|---|---|---|---|
| CoMat 06-153 FELT TIP MARKER, RAPID DRYING | LOCAL | CoMat 06-153 |
Spares
NONESafety Requirements
NONEProcedure
Refer to Repair, VRS2980 TASK 71-51-42-300-003 (REPAIR-003).
Disassemble the backclamps and the connectors to get access to the damaged cables.
Use an applicable forming board to hold the harness.
Make a note of the position of these items: the different types of cable ties, the identification sleeves and the adhesive tape.
Remove only the items which hold the cables that are to be replaced.
Disassemble the harness to get access to the damaged cables.
Use cable of the correct type and length.
Attach the new contacts, refer to Repair, VRS2987 TASK 71-51-42-300-004 (REPAIR-004).
Install the new identification sleeves in the positions noted in Step above, refer to Repair, VRS7002 SPM TASK 70-35-25-300-001-F01 (REPAIR-001).
Replace the cables.
Refer to Repair, VRS2980 TASK 71-51-42-300-003 (REPAIR-003).
Assemble the backclamps and the connectors.
Tie the cables in the positions noted in Step above, refer to Repair, VRS2972 TASK 71-51-42-300-002 (REPAIR-002).
Tie the cables.
Refer to Testing-001 TASK 71-51-42-700-301.
Do a continuity and insulation test
SUBTASK 71-51-42-350-051 Replace the Cables
Use the CoMat 06-153 FELT TIP MARKER, RAPID DRYING marking pen.
Put the repair scheme number VRS2964 on the identification sleeve of the harness, adjacent to the part number.
SUBTASK 71-51-42-850-051 Put the Repair Scheme Number on the Harness