TASK 72-00-32-050-004 LPC/Intermediate Case Module Components - Remove The Air Cooled Oil Cooler (ACOC) Oil Temperature Thermocouple, Removal-011

DMC:V2500-A0-72-00-3250-04A-520A-B|Issue No:001.00|Issue Date:2014-05-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-00-32-050-004 LPC/Intermediate Case Module Components - Remove The Air Cooled Oil Cooler (ACOC) Oil Temperature Thermocouple, Removal-011

General

This TASK gives the procedure to remove the ACOC oil temperature thermocouple.

Fig/item numbers in parentheses in the procedure agree with those used in the IPC. Only the primary Fig/item numbers are used. For the service bulletin alpha-variants refer to the IPC.

For all parts identified in a different Chapter/Section/Subject, the applicable Chapter/Section/Subject comes before the item number.

Apply the approved CoMat 10-058 PENETRATING OIL before the removal of threaded parts. Let the parts soak before removal.

Discard all rubber seal rings removed in this procedure.

The thermocouple removed in the procedure must have its maintenance completed, as given in the Toshiba Component Maintenance Manual (79-32-15).

Seal all openings when the components are disconnected to prevent contamination from unwanted material.

NOTE

To identify the consumable materials refer to the PCI.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 10-058 PENETRATING OIL0AM53CoMat 10-058

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-00-32-030-053 Disconnect the Electrical Connector

    1. Refer to Figure.

    2. Disconnect the electrical connector of the EEC harness EEC Fan Harness (71-51-41, 01-005) from the ACOC oil temperature thermocouple ACOC Oil Temperature Thermocouple (79-32-15, 01-200).

    2. SUBTASK 72-00-32-050-065 Remove the ACOC Oil Temperature Thermocouple

    1. Refer to Figure.

    2. Remove the two bolts ACOC Oil Temperature Thermocouple (79-32-15, 01-210) that attach the ACOC oil temperature thermocouple ACOC Oil Temperature Thermocouple (79-32-15, 01-200) to the ACOC and position the container to catch the oil spill.

    3. Remove the thermocouple ACOC Oil Temperature Thermocouple (79-32-15, 01-200) with the packing ACOC Oil Temperature Thermocouple (79-32-15, 01-220). Discard the packing.

    3. Figure: ACOC oil temperature thermocouple

    ACOC oil temperature thermocouple

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:X222X
Supply Number:CoMat 10-058
Type:sp01
Supply Short Name:CoMat 10-058 PENETRATING OIL
Supply Name:CoMat 10-058 PENETRATING OIL
Suppliers:
ManufacturerRemarks
X222X