TASK 72-00-60-050-010 External Gearbox Components - Remove The Scavenge Oil Filter Element, Removal-014

DMC:V2500-A0-72-00-6050-11A-520A-B|Issue No:004.00|Issue Date:2020-05-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-00-60-050-010 External Gearbox Components - Remove The Scavenge Oil Filter Element, Removal-014

General

This TASK gives the procedure to remove the scavenge oil filter element.

Fig/item numbers in parentheses in the procedure agree with those used in the IPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the IPC.

For all parts identified in a different Chapter/Section/Subject, the applicable Chapter/Section/Subject comes before the Fig/item number.

Apply the approved CoMat 10-058 PENETRATING OIL before the removal of threaded parts. Let the parts soak before removal.

Discard all rubber seal rings removed in this procedure.

The scavenge oil filter element removed in the procedure must be discarded.

Seal all openings when the components are disconnected to prevent contamination from unwanted material.

NOTE

To identify the consumable materials refer to the PCI.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 02-011 FILTER PAPERLOCALCoMat 02-011
CoMat 02-119 LOCKWIRELOCALCoMat 02-119
CoMat 10-058 PENETRATING OILX222XCoMat 10-058

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-00-60-050-073 Drain the Oil Filter Housing (01-550) (Pre SBE 79-0101)

    1. Refer to Figure.

    2. WARNING

      DO NOT GET ENGINE OIL ON YOUR SKIN FOR A LONG TIME. FLUSH THE OIL FROM YOUR SKIN WITH WATER. THE OIL IS POISONOUS AND CAN GO THROUGH YOUR SKIN AND IN TO YOUR BODY.

      WARNING

      USE GOGGLES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

      Cut and discard the CoMat 02-119 LOCKWIRE from the plug Scavenge Oil Filter Housing (79-22-43, 01-120).

    3. Remove the plug and drain the oil into the container 10 L (2 1/2 USGAL) and discard the packing Scavenge Oil Filter Housing (79-22-43, 01-100).

    4. Put the drained oil through a new filter paper (Material No. V02-011) to remove the ferrous and nonferrous debris. Refer to EM TASK 72-00-00-200-008.

    2. SUBTASK 72-00-60-050-108 Drain the Oil Filter Housing (01-550) (SBE 79-0101)

    1. Refer to Figure.

    2. WARNING

      DO NOT GET ENGINE OIL ON YOUR SKIN FOR A LONG TIME. FLUSH THE OIL FROM YOUR SKIN WITH WATER. THE OIL IS POISONOUS AND CAN GO THROUGH YOUR SKIN AND INTO YOUR BODY.

      WARNING

      USE GOGGLES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

      Cut and discard CoMat 02-119 LOCKWIRE from the plug Scavenge Oil Filter Housing (79-22-43, 01-120A).

    3. Remove the plug Scavenge Oil Filter Housing (79-22-43, 01-120A) and packing Scavenge Oil Filter Housing (79-22-43, 01-100A).

    4. Drain the oil into the CONTAINER 10 L (2 1/2USGAL).

    5. Put the drained oil through a new CoMat 02-011 FILTER PAPER to remove the ferrous and nonferrous debris. Refer to EM TASK 72-00-00-200-008.

    3. SUBTASK 72-00-60-050-074 Remove the Oil Filter Cover Assembly (01-250)

    1. Refer to Figure.

    2. Remove the bolts Scavenge Oil Filter Housing (79-22-43, 01-145) and the washers Scavenge Oil Filter Housing (79-22-43, 01-150).

    3. Remove the cover Scavenge Oil Filter Housing (79-22-43, 01-250) and discard the packing Scavenge Oil Filter Housing (79-22-43, 01-155).

    4. SUBTASK 72-00-60-050-075 Remove the Scavenge Oil Filter Element (01-100)

    1. Refer to Figure.

    2. Remove the scavenge oil filter element Scavenge Oil Filter Element (79-22-44, 01-100) from the oil filter housing Scavenge Oil Filter Housing (79-22-43, 01-550) and discard the filter element.

    5. SUBTASK 72-00-60-050-076 Seal all Openings

    1. Install the applicable covers, caps or plugs on all of the openings.

    6. Figure: Scavenge Oil Filter Element

    Scavenge Oil Filter Element

Requirements After Job Completion

Follow-On Conditions

NONE
Change Type:

Replace incorrect graphic (CAS-65147-H8D1J2)

Manufacturer Code:LOCAL
Enterprise Name:LOCALLY SUPPLIED
Manufacturer Code:X222X
Enterprise Name:N/A – REFER TO APPLICABLE COMAT SUFFIX
Manufacturer Code:LOCAL
Supply Number:CoMat 02-011
Type:sp01
Supply Short Name:CoMat 02-011 FILTER PAPER
Supply Name:CoMat 02-011 FILTER PAPER
Specification Groups:
Doc NumberType
OMAT:1/143WHATMAN 42
Suppliers:
ManufacturerRemarks
LOCAL
24853
K6835
U1185
Manufacturer Code:LOCAL
Supply Number:CoMat 02-119
Type:sp01
Supply Short Name:CoMat 02-119 LOCKWIRE
Supply Name:CoMat 02-119 LOCKWIRE
Specification Groups:
Doc NumberType
SAE AS9226 Part Number MS-9226-04 (0.032 IN DIA.)
Suppliers:
ManufacturerRemarks
LOCAL
51563
81343
V508V
Manufacturer Code:X222X
Supply Number:CoMat 10-058
Type:sp01
Supply Short Name:CoMat 10-058 PENETRATING OIL
Supply Name:CoMat 10-058 PENETRATING OIL
Suppliers:
ManufacturerRemarks
X222X