TASK 72-32-71-200-007 LPC Bleed Valve Sleeve Bearing - Examine, Inspection-007

DMC:V2500-A0-72-32-7162-00A-300A-C|Issue No:001.00|Issue Date:2013-11-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-32-71-200-007 LPC Bleed Valve Sleeve Bearing - Examine, Inspection-007

Effectivity

FIG/ITEM

PART NO.

02-089

5A0788

02-091

5A0787

02-093

5A0786

02-095

5A0785

02-097

5A0784

02-099

5A0783

02-101

5A0782

02-103

5A0781

02-105

5A0780

02-109

5A0783

02-108

5A0780

General

This TASK gives the procedure for the inspection of the sleeve bearing. For the other bleed valve support and arms parts, refer to TASK 72-32-71-200-000.

The policy that is necessary for inspection is given in the SPM TASK 70-20-01-200-501.

All the parts must be cleaned before any part is examined. Refer to TASK 72-32-71-100-000.

All the parts must be visually examined for damage, corrosion and wear. Any defects that are not identified in the procedure must be referred to IAE.

The procedure for those parts which have a crack test is given in Step. Do the test before the parts is visually examined.

Do not discard any part until you are sure there are no repairs available. Refer to the inspections in Repair before a discarded part is used again or oversize parts are installed.

Parts which should be discarded can be held although no repair is available. The repair of a discarded part could be shown to be necessary at a later date.

All the parts must be examined to make sure that all the repairs have been completed satisfactorily.

The practices and processes referred to in the procedure by the TASK numbers are in the SPM.

References

Refer to the SPM for data on these items.

Definitions of Damage, SPM TASK 70-02-02-350-501

Inspection of parts, SPM TASK 70-20-01-200-501

Some data on these items are contained in this TASK. For more data on these items refer to the SPM.

Method of Testing for Crack Indications

Chemical Processes

Surface Protection

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NameManufacturerPart Number / IdentificationQuantityRemark
Fluorescent Penetrant Inspection EquipmentLOCALFluorescent penetrant inspection equipment

Consumables, Materials and Expendables

NONE

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-32-71-230-069 Examine the Sleeve Bearing for Cracks

    1. Clean the parts. Refer to TASK 72-32-71-100-000.

      2. Do the test for cracks on the parts that are given below. Use the applicable fluorescent penetrant inspection procedure.

        PART IDENT

        TASK/SUBTASK

        Sleeve Bearing

        1. Cracked

        1. Reject

    2. SUBTASK 72-32-71-220-105 Examine the Sleeve Bearing (02-089, 02-091, 02-093, 02-095, 02-097, 02-099, 02-101, 02-103, 02-105 and 02-109) Outside Diameter at Location 1

    1. Refer to Figure.

      2. Examine the outside diameter at location 1.

        1. Worn.

          1. If the diameter is not less than 0.626 in. (15.90 mm)

          1. Accept

          2. If the diameter is less than 0.626 in. (15.90 mm)

          1. Reject

    3. SUBTASK 72-32-71-220-106 Examine the Sleeve Bearing (02-089, 02-091, 02-093, 02-095, 02-097, 02-099, 02-101, 02-103, 02-105 and 02-109) Inside Diameter at Location 2

    1. Refer to Figure.

      2. Examine the inside diameter at location 2.

        1. Worn.

          1. If the diameter is not more than 0.5005 in. (12.713 mm)

          1. Accept

          2. If the diameter is more than 0.5005 in. (12.713 mm)

          1. Reject

    4. SUBTASK 72-32-71-220-107 Examine the Sleeve Bearing (02-089, 02-091, 02-093, 02-095, 02-097, 02-099, 02-101, 02-103, 02-105 and 02-109) TFE Liner at Location 3

    1. Refer to Figure.

      2. Examine the TFE liner at location 3.

        1. Peeled

        1. Reject

    5. SUBTASK 72-32-71-220-108 Examine the Sleeve Bearing (02-089, 02-091, 02-093, 02-095, 02-097, 02-099, 02-101, 02-103, 02-105 and 02-109) Flange Thickness at Location 4

    1. Refer to Figure.

      2. Examine the bearing (02-089) flange thickness at location 4.

        1. If the flange thickness is between 0.0536 and 0.0555 in. (1.360 and 1.410 mm)

        1. Accept

        2. Less than in Step

        1. Reject

      3. Examine the bearing (02-091) flange thickness at location 4.

        1. If the flange thickness is between 0.0546 and 0.0564 in. (1.385 and 1.435 mm)

        1. Accept

        2. Less than in Step

        1. Reject

      4. Examine the bearing (02-093) flange thickness at location 4.

        1. If the flange thickness is between 0.0556 and 0.0574 in. (1.410 and 1.460 mm)

        1. Accept

        2. Less than in Step

        1. Reject

      5. Examine the bearing (02-095) flange thickness at location 4.

        1. If the flange thickness is between 0.0565 and 0.0584 in. (1.435 and 1.485 mm)

        1. Accept

        2. Less than in Step

        1. Reject

      6. Examine the bearing (02-097) flange thickness at location 4.

        1. If the flange thickness is between 0.0575 and 0.0595 in. (1.460 and 1.510 mm)

        1. Accept

        2. Less than in Step

        1. Reject

      7. Examine the bearing (02-099) flange thickness at location 4.

        1. If the flange thickness is between 0.0585 and 0.0604 in. (1.485 and 1.535 mm)

        1. Accept

        2. Less than in Step

        1. Reject

      8. Examine the bearing (02-101) flange thickness at location 4.

        1. If the flange thickness is between 0.0595 and 0.0614 in. (1.510 and 1.560 mm)

        1. Accept

        2. Less than in Step

        1. Reject

      9. Examine the bearing (02-103) flange thickness at location 4.

        1. If the flange thickness is between 0.0605 and 0.0624 in. (1.535 and 1.585 mm)

        1. Accept

        2. Less than in Step

        1. Reject

      10. Examine the bearing (02-105) flange thickness at location 4.

        1. If the flange thickness is between 0.0615 and 0.0633 in. (1.560 and 1.610 mm)

        1. Accept

        2. Less than in Step

        1. Reject

    6. Figure: Locations on the sleeve bearing

    Locations on the sleeve bearing

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:LOCAL
Enterprise Name:LOCALLY SUPPLIED
Manufacturer Code:LOCAL
Tool Number:Fluorescent penetrant inspection equipment
Tool Name:Fluorescent Penetrant Inspection Equipment