Preliminary Requirements

Procedure

1. SUBTASK 72-32-85-350-075 Remove Defective Area of Damage

   1. 
      CAUTION
      THE FAN CASE IS MADE FROM TITANIUM ALLOY AND IS THIN IN SOME AREAS. IF YOU HIT THE FAN CASE WITH A CHISEL OR SCRAPER YOU CAN MAKE IT UNSERVICEABLE.
      
      CAUTION
      YOU MUST ALWAYS TRY TO POINT THE CHISEL OR SHARP BLADE PARALLEL WITH THE SURFACE OF THE FAN CASE.
      
      CAUTION
      STOP MACHINING AS SOON AS THE FILES, CUTTERS OR MACHINING BITS ARE THROUGH THE LINING MATERIAL. USE A STOP-MACHINING OR SLEEVE OR OTHER PENETRATION LIMITING DEVICE TO PREVENT DAMAGE TO THE CASING MATERIAL.
      
      CAUTION
      DO NOT USE POWERED TOOLS WITH STEEL CHISEL OR SIMILAR BITS.
      
      CAUTION
      DO NOT OPERATE WITHOUT SAFETY GOGGLES AND OTHER GUARDS EQUIPMENT. FLYING PARTICLES CAN CAUSE INJURY.

      NOTE

      Keep the material removal to the minimum necessary to remove damaged area.

      Remove loose and damaged material from repair area.

      1. Use hand held pneumatic grinder and rotary files.

      2. Take care not to damage the GRC layer which is sandwiched between the two layers of honeycomb in this area.

      3. Refer to Figure.

   2. Check security of panels adjacent to repair area.

      1. Check visually and by tapping.

      2. A hollow sound is indicative of suspect bond.

      3. Remove any unsound material.

      4. If damage has reached the GRC layer or below the GRC layer.

      5. Repair, refer to VRS1557 TASK 72-32-85-300-018 (REPAIR-018).

   3. Make repair areas rough.

      1. Use CoMat 05-016 GARNET PAPER, 80-GRIT.

   4. Remove any remaining debris.

      1. Use vacuum cleaner.

   5. Immediately dry out the area using air blast.

      1. Use oil free air.

2. SUBTASK 72-32-85-110-070 Remove the Grease from the Repair Area

   1. 
      WARNING
      ALWAYS MAKE SURE THERE IS SUFFICIENT VENTILATION IN THE WORK AREA. EYE PROTECTION MUST ALWAYS BE USED. DO NOT LET THE SOLVENT CLEANER OR ITS VAPOR TOUCH THE EYES OR SKIN. PROTECTIVE CLOTHING AND FACE MASK MUST ALWAYS BE USED. ALWAYS KEEP OPEN FLAMES AWAY FROM THE WORK AREA. IT IS THE RESPONSILIBILTY OF THE OPERATOR TO OBTAIN AND OBSERVE THE MANUFACTURERS MATERIAL SAFETY SHEETS FROM THE CONSUMABLE MATERIALS INFORMATION SUCH AS HAZARDOUS INGREDIENTS, PHYSICAL/CHEMICAL CHARACTERISTICS, FIRE, EXPLOSION, REACTIVITY, HEALTH HAZARD DATA, PRECAUTIONS FOR SAFE HANDLING, USE AND CONTROL MEASURES AND ALSO TO TAKE LOCAL REGULATIONS INTO CONSIDERATION.

      Fully remove any grease from the repair area except the blue filler surface.

      1. Refer to the SPM TASK 70-11-26-300-503.

      2. Use CoMat 01-076 METHYL ETHYL KETONE with CoMat 02-099 LINT-FREE CLOTH.

   2. Immediately dry out the cleaned repair area with air blast.

      1. Use oil free air.

3. SUBTASK 72-32-85-360-061 Prepare Filler Material

   1. Measure out materials by weight.

      1. Ref to the SPM TASK 70-36-02-360-501.

      2. Use CoMat 08-006 FILLER, TWO PACK.

   2. Mix the two parts by kneading until the paste is a constant blue color. No streaks permitted.

      1. Use putty knife.

4. SUBTASK 72-32-85-350-076 Apply Filler Material

   1. Fill the filler slightly more than necessary level in the damaged area.

      1. Refer to the SPM TASK 70-36-02-360-501.

      2. Use air powered sealant gun or equivalent.

      3. Make sure that the repair area is fully filled with no air pockets.

      4. If the complete fan track is to be filled to the depth to the GRC layer, start at the bottom and work both sides. The filler will gradually set.

      5. If any sagging is apparent, locally produced supports will be necessary.

   2. 
      CAUTION
      THE MAXIMUM TEMPERATURE WHICH CAN BE USED TO CURE THE FILLER IS 176 DEG F (80 DEG C).

      Cure the filler.

      1. The cure times and temperatures are given in Figure.

   3. 
      CAUTION
      DO NOT OPERATE WITHOUT SAFETY GOGGLES AND OTHER GUARD EQUIPMENT. FLYING PARTICLES CAN CAUSE INJURY.

      NOTE

      The minimum cure time is one hour.

      Blend the filler to the contors.

      1. Use CoMat 05-016 GARNET PAPER, 80-GRIT.

      2. Refer to Figure.

   4. Remove debris.

      1. Use vacuum cleaner.

5. SUBTASK 72-32-85-220-083 Examine the repair Area

   1. Examine the surface of repaired area.

      1. Make sure that the filled surface is smooth and flat.

      2. A Step is acceptable if less than 0.02 in. (0.5 mm).

      3. If necessary do this TASK again.

      4. Refer to Figure.

Figure: Repair the attrition lining down to GRC layer (SBE 72-0103)

Repair the attrition lining down to GRC layer (SBE 72-0103)



Figure: Curing Chart of Filling Material (08-006)

Curing Chart of Filling Material (08-006)