TASK 72-32-80-530-001-B00 LPC Assembly - Pack The LPC Assembly, Storage-001

DMC:V2500-A5-72-32-8000-00B-830A-B|Issue No:001.00|Issue Date:2013-11-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

V2500-A5

Common Information

TASK 72-32-80-530-001-B00 LPC Assembly - Pack The LPC Assembly, Storage-001

General

Fig/item numbers in parentheses in the procedure agree with those used in the IPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the IPC.

For all parts identified in a different Chapter/Section/Subject, the applicable Chapter/Section/Subject comes before the Fig/item number.

For standard torque data and procedures refer to the SPM TASK 70-41-00-400-501, SPM TASK 70-41-01-400-501 and SPM TASK 70-41-02-410-501.

Lubricate all threads and abutment faces of nuts and bolts with CoMat 10-077 APPROVED ENGINE OILS unless other lubricants are referred to in the procedure.

Refer to the V2500 Illustrated Tool and Equipment Manual (ITEM) Pub ref ITE-V2500-1IA, for the illustrations of the special tools given in this procedure.

Make sure that all flange faces and tool faces that touch are very clean.

NOTE

To identify the consumable materials refer to the PCI.

NOTE

Special tools are identified in the procedure by the tool primary number.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NameManufacturerPart Number / IdentificationQuantityRemark
Four legged slingLOCALFour legged sling
IAE 1J12213 LPC Vertical sling0AM53IAE 1J122131
IAE 5J13194 Shipping container0AM53IAE 5J131941
IAE 1J12541 Holding support0AM53IAE 1J125411

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 10-077 APPROVED ENGINE OILSLOCALCoMat 10-077
CoMat 12-022 DESICCANT SELF INDICATINGLOCALCoMat 12-022

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-32-80-530-056 Remove the Cover Assembly of the Shipping Container

    1. Refer to Figure.

    2. Attach a suitable four legged sling to a hoist.

    3. Move the hoist over the IAE 5J13194 Shipping container 1 off and attach the four legged sling to the four cover assembly lift rings.

    4. Release all the butterfly catches.

    5. Lift the cover assembly of the shipping container away from the shipping container base and put it on a suitable surface.

    6. Remove the sling from the hoist.

    2. SUBTASK 72-32-80-530-057 Install the LPC Assembly into the Carriage Base of the Shipping Container

    1. Refer to Figure.

    2. Make sure that the LPC assembly together with IAE 1J12541 Holding support 1 off. If is not, refer to TASK 72-32-80-440-001-B00 (ASSEMBLY, CONFIG-002).

      3. Prepare the carriage base.

      1. Release the handling bolt on the carriage base. Move the locator top into the open position.

      2. Make sure that all the faces are clean on the flange and tool faces that touch.

      4. Attach the IAE 1J12213 LPC Vertical sling 1 off to the LPC assembly.

      1. Install the three brackets (part of the LPC vertical sling) to the disk front flange. The three brackets must be equally apart.

      2. Attach the hoist to the LPC vertical sling.

    5. Move the LPC assembly and put it over the carriage base.

    6. Remove the LPC vertical sling from the LPC assembly and put it on an applicable work surface.

    7. Remove the sling from the hoist.

    8. Install the locator top on to the LPC assembly and handling bolt.

    9. Torque the handling bolt by hand.

    3. SUBTASK 72-32-80-530-058 Seal the Shipping Container

    1. Refer to Figure.

    2. Attach the hoist to the four legged sling that is attached to the cover assembly of the shipping container.

    3. Lift the cover assembly of the shipping container put it over the LPC assembly.

    4. Lower the cover assembly of the shipping container on to the carriage base.

    5. Attach the cover assembly of the shipping container to the carriage base with all the butterfly catches.

    6. Remove the four legged sling from the lift rings of the cover assembly.

    7. Remove the four legged sling from the hoist and put it on an applicable work surface.

    4. SUBTASK 72-32-80-530-059 Put the Desiccant and the Records into the Shipping Container

    1. Refer to Figure.

    2. Put the correct amount of desiccant into the desiccant receptacle. Follows the instructions given on the shipping container cover assembly adjacant to the desiccant receptacle. Use CoMat 12-022 DESICCANT SELF INDICATING. Replace the desiccant receptacle cover.

    3. Complete the relevant documentation. Put the documentation into the record receptacle. Put the cover on to the record receptacle.

    5. SUBTASK 72-32-80-530-060 Do the Subsequent Check after the Shipping Container is Sealed

    1. Examine the humidity indicator to make sure it is safe at the times shown. 24 hours, 7 days and then at regular 28 day cycles.

      2. If the humidity indicator changes color from blue, do the subsequents steps.

        1. Remove the shipping container cover assembly from the carriage base.

        1. Attach the four legged sling to a hoist.

        2. Move the hoist over the shipping container attach the four legged sling to the four shipping container cover lift rings.

        3. Release all the butterfly catches.

        4. Remove the shipping container cover assembly and put it on a suitable surface.

      2. Do a visual inspection for corrosion and damage.

        3. Install the shipping container cover assembly on to the carriage base.

        1. Lift the shipping container cover assembly and put it on to the carriage base.

        2. Attach the shipping container cover assembly to the carriage base with all the butterfly catches.

      4. Remove the desiccant from the desiccant receptacle and replace it with new desiccant. Follow the instructions given on the the shipping container cover assembly, adjacant receptacle for the correct amount, Use CoMat 12-022 DESICCANT SELF INDICATING. Replace the desiccant receptacle cover.

      5. Do Step again.

    6. Figure: LP compressor booster stage assembly shipping equipment

    LP compressor booster stage assembly shipping equipment

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:LOCAL
Enterprise Name:LOCALLY SUPPLIED
Manufacturer Code:X333X
Supply Number:CoMat 10-077
Type:sp01
Supply Short Name:CoMat 10-077 APPROVED ENGINE OILS
Supply Name:CoMat 10-077 APPROVED ENGINE OILS
Specification Groups:
Doc NumberType
For V2500-A1/A5/D5 models - Refer to V2500 Service Bulletin ENG-79-0108
For V2500-E5 model - Refer to Service Bulletin E5-79-0001
Suppliers:
ManufacturerRemarks
X333X
Manufacturer Code:K6835
Supply Number:CoMat 12-022
Type:sp01
Supply Short Name:CoMat 12-022 DESICCANT SELF INDICATING
Supply Name:CoMat 12-022 DESICCANT SELF INDICATING
Specification Groups:
Doc NumberType
SILICA GEL B.S.3523 COBALT CHLORIDE TYPE
Suppliers:
ManufacturerRemarks
K6835
22627
LOCAL
K8888
KD685
Manufacturer Code:LOCAL
Tool Number:Four legged sling
Tool Name:Four legged sling
Manufacturer Code:0AM53
Tool Number:IAE 1J12213
Tool Name:IAE 1J12213 LPC Vertical sling
Manufacturer Code:0AM53
Tool Number:IAE 1J12541
Tool Name:IAE 1J12541 Holding support
Manufacturer Code:0AM53
Tool Number:IAE 5J13194
Tool Name:IAE 5J13194 Shipping container