TASK 72-32-89-200-001-B00 Fan Case Outer Acoustic Transition Liner Panel - Examine, Inspection-001 - SBE 72-0103

DMC:V2500-A1-72-32-8900-00B-300A-C|Issue No:001.00|Issue Date:2013-11-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

V2500-A1

Common Information

TASK 72-32-89-200-001-B00 Fan Case Outer Acoustic Transition Liner Panel - Examine, Inspection-001 - SBE 72-0103

Effectivity

FIG/ITEM

PART NO.

01-100

5R0174

General

This TASK gives the procedure for the inspection of the transition panels.

Fig/item numbers in parentheses in the procedure agree with those used in the IPC.

The policy that is necessary for inspection is given in SPM TASK 70-20-01-220-501.

All parts must be cleaned before any part is examined. Refer to the SPM TASK 70-11-03-300-503.

All parts must be visually examined for damage, corrosion and wear. Any defects that are not identified in the procedure must be referred to IAE.

The procedure for those parts which must have a crack test is given in Step. Do the test before the part is visually examined. Limits for cracks are given in the SUBTASK for each part.

Do not discard any part until you are sure there are no repairs available. Refer to the instructions in repair before a discarded part is used again.

Parts which should be discarded can be held although no repair is available. The repair of a discarded part could be shown to be necessary at a later date.

All parts must be examined to make sure that all repairs have been completed satisfactorily.

The practices and processes referred to in the procedure by the TASK numbers are in the SPM.

References

Refer to the SPM for data on these items

Definitions of Damage, SPM TASK 70-02-02-350-501

Inspection of Parts, SPM TASK 70-20-01-200-501

Some data on these items is contained in this TASK. For more data on these items refer to the SPM.

Method of Testing for Crack Indications

Chemical Processes

Surface Protection

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

NONE

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-32-89-230-052 Examine the Transition Panels

    1. NOTE

      For the method to clean the part, refer to the SPM TASK 70-11-03-300-503.

      Clean the part. Refer to TASK 72-32-89-100-000.

      2. Do the crack test on the part that is given below. Use the applicable penetrant inspection procedure.

        PART IDENT

        TASK/SUBTASK

        Transition panel

        1. Cracked

        1. Reject

    2. SUBTASK 72-32-89-220-061 Examine the Outer Surfaces at Location 1

    1. Refer to Figure.

      2. Any nicks

      1. Repair, VRS1562 TASK 72-32-89-300-006 (REPAIR-006)

      3. Any scores

      1. Repair, VRS1562 TASK 72-32-89-300-006 (REPAIR-006)

    3. SUBTASK 72-32-89-220-062 Examine the Bolt Holes at Location 2

    1. Refer to Figure.

      2. Any scores

      1. Repair, VRS1562 TASK 72-32-89-300-006 (REPAIR-006)

    4. SUBTASK 72-32-89-220-063 Examine the Counter Bore at Location 3

    1. Refer to Figure.

      2. Any scores

      1. Repair, VRS1562 TASK 72-32-89-300-006 (REPAIR-006)

    5. Figure: Inspection of the transition panel

    Inspection of the transition panel

Requirements After Job Completion

Follow-On Conditions

NONE