TASK 71-11-43-200-302 Air Intake Cowl Harness - Examine The P2T2 - 4010VC And 4013VC Cable Assembly, Inspection-002

DMC:V2500-A0-71-11-4300-01A-310A-C|Issue No:001.00|Issue Date:2013-11-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 71-11-43-200-302 Air Intake Cowl Harness - Examine The P2T2 - 4010VC And 4013VC Cable Assembly, Inspection-002

Effectivity

FIG/ITEM

PART NO.

01-500

740-3235-503

01-500

740-3235-505

01-500

740-3235-507

01-500

740-3235-509

01-500

740-3235-511

General

Fig/item numbers in parentheses in the procedure agree with those used in the IPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the IPC.

The policy that is necessary for inspection is given in the SPM TASK 70-20-01-200-501

All the parts must be cleaned before they are examined, refer to Cleaning-000 TASK 71-11-43-100-300.

All the parts must be visually examined for damage, corrosion and wear. Any defects that are not identified in the procedure must be referred to IAE.

A ** following repair referenced in this inspection indicates that the repair is not yet published in the current revision of the manual and the part must be rejected. Contact IAE for additional information concerning FAA approved repair date.

Do not discard any part until you are sure there are no repairs available. Refer to the instructions in Repair before a discarded part is used again or oversize parts are installed.

Parts which should be discarded can be held although no repair is available. The repair of a discarded part could be shown to be necessary at a later date.

Reference

Refer to the SPM for data on these items.

Definitions of Damage, SPM TASK 70-02-02-350-501.

Inspection of Parts, SPM TASK 70-20-00-200-501.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

NONE

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 71-11-43-220-054 Examine the Connectors

      1. Cracked

      1. VRS2979 (Repair-001) TASK 71-11-43-300-001.

      2. Broken

      1. VRS2979 (Repair-001) TASK 71-11-43-300-001.

      3. Coupling nuts

        1. Threads

          1. Pick-up

          1. VRS2979 (Repair-001) TASK 71-11-43-300-001.

          2. Crossed or stripped

          1. VRS2979 (Repair-001) TASK 71-11-43-300-001.

      4. Contact pins

        1. Bent

        1. VRS2986 (Repair-002) TASK 71-11-43-300-002.

        2. Worn (do the check with a new socket)

        1. VRS2986 (Repair-002) TASK 71-11-43-300-002.

      5. Contact sockets

        1. Bent

        1. VRS2986 (Repair-002) TASK 71-11-43-300-002.

        2. Worn (do the check with a new pin)

        1. VRS2986 (Repair-002) TASK 71-11-43-300-002.

    2. SUBTASK 71-11-43-220-055 Examine the Cables

      1. Burned

      1. VRS2927 (Repair-003) TASK 71-11-43-300-003.

      2. Frayed

      1. VRS2927 (Repair-003) TASK 71-11-43-300-003.

      3. Fused

      1. VRS2927 (Repair-003) TASK 71-11-43-300-003.

      4. Chafed

      1. VRS2927 (Repair-003) TASK 71-11-43-300-003.

      5. Loose

        1. Crimp joints

        1. VRS2986 (Repair-002) TASK 71-11-43-300-002.

    3. SUBTASK 71-11-43-220-056 Examine the Ties

      1. Chafed

      1. VRS2971 (Repair-004) TASK 71-11-43-300-004.

      2. Frayed

      1. VRS2971 (Repair-004) TASK 71-11-43-300-004.

Requirements After Job Completion

Follow-On Conditions

NONE