TASK 72-00-32-450-017 LPC/Intermediate Case Module Components - Install The Oil Pressure Transmitter, Installation-024

DMC:V2500-A0-72-00-3250-15A-720A-B|Issue No:001.00|Issue Date:2014-05-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-00-32-450-017 LPC/Intermediate Case Module Components - Install The Oil Pressure Transmitter, Installation-024

General

Fig/item numbers in parentheses in the procedure agree with those used in the EIPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the EIPC.

Lubricate all threads and abutment faces of nuts and bolts with CoMat 10-039 ENGINE OIL, unless other lubricants are referred to in the procedure.

For the torque tightening procedures refer to the SPM TASK 70-41-00-400-501 and SPM TASK 70-41-01-400-501.

For the data on electrical connectors refer to the SPM TASK 70-43-00-400-501 and the SPM TASK 70-43-01-400-501.

For lockwire data and procedures refer to the SPM TASK 70-42-05-400-501.

NOTE

To identify the consumable materials refer to the Overhaul Processes and Consumables Index (PCI).

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NameManufacturerPart Number / IdentificationQuantityRemark
Torque wrench, range 0 to 250 lbfin (0 to 20 Nm)LOCALTorque Wrench 0-250

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 01-002 SOLVENT, DELETED.0AM53CoMat 01-002
CoMat 02-099 LINT-FREE CLOTHLOCALCoMat 02-099
CoMat 02-126 LOCKWIRELOCALCoMat 02-126
CoMat 10-039 ENGINE OILLOCALCoMat 10-039

Spares

NONE

Safety Requirements

WARNING

DO NOT LET ENGINE OIL STAY ON YOUR SKIN FOR A LONG TIME. FLUSH THE OIL FROM YOUR SKIN WITH WATER. THE OIL IS POISONOUS AND CAN GO THROUGH YOUR SKIN AND IN TO YOUR BODY.

CAUTION

DO NOT LET ENGINE OIL FALL ON THE ENGINE. UNWANTED OIL MUST BE REMOVED IMMEDIATELY WITH A CLEAN CLOTH. THE OIL CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.

Procedure

    1. SUBTASK 72-00-32-110-053 Clean the Parts

    1. Refer to Figure.

    2. WARNING

      DO NOT GET THE CLEANING FLUID ON YOUR SKIN OR IN YOUR EYES. PUT ON PROTECTIVE CLOTHING, GLOVES, GOGGLES AND A MASK. USE THE FLUID IN A WELL VENTILATED AREA. DO NOT BREATHE THE GAS. IF YOU GET THE FLUID ON YOUR SKIN OR IN YOUR EYES, FLUSH IT AWAY WITH WATER. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.

      Use the CoMat 02-099 LINT-FREE CLOTH and the CoMat 01-002 SOLVENT, DELETED. to clean the interfaces between the bracket General Services Harness (71-51-43, 05-990), the transmitter OIL-OIL PRESSURE TRANSMITTER (79-33-15, 01-010), the bolts OIL-OIL PRESSURE TRANSMITTER (79-33-15, 01-020), the electrical connector and the oil tubes.

    3. Wipe the components with a clean piece of lint free cloth before the fluid dries.

    2. SUBTASK 72-00-32-440-051 Install the Oil Pressure Transmitter

    1. Refer to Figure.

    2. Remove the blanking caps from the components.

    3. Hold the oil pressure transmitter OIL-OIL PRESSURE TRANSMITTER (79-33-15, 01-010) on to the bracket General Services Harness (71-51-43, 05-990), in the position noted on removal. Attach the oil pressure transmitter OIL-OIL PRESSURE TRANSMITTER (79-33-15, 01-010) on to the bracket General Services Harness (71-51-43, 05-990) with the bolts OIL-OIL PRESSURE TRANSMITTER (79-33-15, 01-020). Torque the bolts OIL-OIL PRESSURE TRANSMITTER (79-33-15, 01-020) to 100 lbf.in (11.3 Nm).

    4. Connect the oil tubes to the oil pressure transmitter OIL-OIL PRESSURE TRANSMITTER (79-33-15, 01-010). Torque the tube nuts to between 135 and 145 lbf.in (15.3 and 16.4 Nm).

    5. Connect the electrical connector to the oil pressure transmitter OIL-OIL PRESSURE TRANSMITTER (79-33-15, 01-010).

    3. SUBTASK 72-00-32-210-072 Visually Inspect the Electrical Backshells and Cable Clamps

    1. Refer to Figure.

    2. Make sure that all the applicable connectors, backshells and cable clamps are secure.

    3. Make sure that all the applicable backshells and cable clamps are safetied with CoMat 02-126 LOCKWIRE. Refer to the SPM TASK 70-42-05-400-501.

    4. Figure: Oil pressure transmitter

    Oil pressure transmitter

    Figure: Visually inspect the backshells and cable clamps

    Visually inspect the backshells and cable clamps

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:LOCAL
Enterprise Name:LOCALLY SUPPLIED
Manufacturer Code:X111X
Supply Number:CoMat 01-002
Type:sp01
Supply Short Name:CoMat 01-002 SOLVENT, DELETED.
Supply Name:CoMat 01-002 SOLVENT, DELETED.
Specification Groups:
Doc NumberType
wiring harnesses. Where CoMat 01‐002 is specified to clean mechanical components, use one or more of the solvents that SPM TASK 70‐11‐26‐300‐503 specifies as applicable.DELETED. Where CoMat 01‐002 is specified to clean electrical contacts or wiring harnesses, use one or more of the solvents that SPM TASK 70‐11‐57‐110‐501 specifies to clean electrical contacts or
Suppliers:
ManufacturerRemarks
X111X
Manufacturer Code:X222X
Supply Number:CoMat 02-099
Type:sp01
Supply Short Name:CoMat 02-099 LINT-FREE CLOTH
Supply Name:CoMat 02-099 LINT-FREE CLOTH
Specification Groups:
Doc NumberType
WHERE COMAT 02-099 IS SPECIFIED WITH NO SUFFIX, USE COMAT 02-099A OR COMAT 02-099B.
Suppliers:
ManufacturerRemarks
X222X
Manufacturer Code:K6835
Supply Number:CoMat 02-126
Type:sp01
Supply Short Name:CoMat 02-126 LOCKWIRE
Supply Name:CoMat 02-126 LOCKWIRE
Specification Groups:
Doc NumberType
DTD 189A, 0.028 TO 0.032 IN DIA
Suppliers:
ManufacturerRemarks
K6835
KB362
LOCAL
U06C8
Manufacturer Code:LOCAL
Supply Number:CoMat 10-039
Type:sp01
Supply Short Name:
Supply Name:CoMat 10-039 ENGINE OIL
Specification Groups:
Doc NumberType
DELETED
Suppliers:
ManufacturerRemarks
LOCAL
Manufacturer Code:LOCAL
Tool Number:Torque Wrench 0-250
Tool Name:Torque wrench, range 0 to 250 lbfin (0 to 20 Nm)