TASK 72-41-21-200-009-A00 HPC Stage 10 Rotor Path Ring - Examine, Inspection-009

DMC:V2500-A0-72-41-2126-00A-300A-C|Issue No:002.00|Issue Date:2018-08-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-41-21-200-009-A00 HPC Stage 10 Rotor Path Ring - Examine, Inspection-009

Effectivity

FIG/ITEM

PART NO.

04-300

6A3654

General

This TASK gives the procedure for the inspection of the stage 10 rotor path ring.

Fig/item numbers in parentheses in the procedure agree with those used in the IPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the IPC.

The policy that is necessary for inspection is given in the SPM TASK 70-20-01-200-501.

All the parts must be cleaned before any part is examined.

All the parts must be visually examined for damage, corrosion and wear. Any defects that are not identified in the procedure must be referred to IAE.

The procedure for the parts which must have a crack test is given in Step. Do the crack test before a part is visually examined.

Do not discard any part until you are sure there are no repairs available. Refer to the instructions in Repair before a discarded part is used again or oversize parts are installed.

Parts which should be discarded can be held although no repair is available. The repair of a discarded part can be shown to be necessary at a subsequent date.

All the parts must be examined to make sure that all the repairs have been completed satisfactorily.

The practices and processes referred to in the procedure by the TASK/SUBTASK number are in the SPM.

References

Refer to the SPM for data on these items:

Definition of Damage, SPM TASK 70-02-02-350-501,

Record and Control of the Lives of Parts, SPM TASK 70-05-00-220-501,

Inspection of Parts, SPM TASK 70-20-01-200-501.

Some data on these items are contained in this TASK. For more data on these items refer to the SPM:

Methods of Testing for Crack Indications,

Chemical Processes,

Surface Protection.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

NONE

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-41-21-230-232 Examine the Stage 10 Rotor Path Ring for Cracks

    1. Clean the parts. Refer to TASK 72-41-21-100-000 (CLEANING-000).

      2. Do the test for cracks on the part that is given below.

        PART IDENT

        TASK/SUBTASK

        Stage 10 rotor path ring

        1. Cracked.

        1. Reject.

    2. SUBTASK 72-41-21-220-114 Examine the Stage 10 Rotor Path Ring Lining at Location 1053

    1. Refer to Figure.

      2. Scored.

        1. Up to 0.005 in. (0.13 mm) in depth.

        1. Accept.

        2. More than Step.

        1. Repair, VRS6022 TASK 72-41-21-300-016 (REPAIR-016).

      3. Chipped.

      1. Repair, VRS6022 TASK 72-41-21-300-016 (REPAIR-016).

      4. Worn.

        1. If the radius is between 10.2319 in. and 10.2359 in. (259.89 mm to 259.99 mm).

        1. Accept.

        2. If the lining diameter is more than in Step.

        1. Repair, VRS6022 TASK 72-41-21-300-016 (REPAIR-016).

    3. SUBTASK 72-41-21-220-115 Examine the Stage 10 Rotor Path Ring Faces at Locations 1, 2, 1175 and 1110

    1. Refer to Figure.

      2. Galled.

        1. Not more than 0.002 in. (0.05 mm) in depth.

        1. Accept.

        2. More than in Step.

        1. Repair VRS6098, TASK 72-41-21-300-015 (REPAIR-015).

      3. Scored.

        1. Not more than 0.002 in. (0.05 mm) in depth.

        1. Accept.

        2. More than in Step.

        1. Repair VRS6098, TASK 72-41-21-300-015 (REPAIR-015).

      4. Location 1110.

        1. If the diameter is between 21.157 in. and 21.161 in. (537.39 mm and 537.49 mm).

        1. Accept.

        2. If the diameter is less than in Step.

        1. Reject.

      5. Location 1175.

        1. If the diameter is between 21.158 in. and 21.161 in. (537.40 mm and 537.48 mm).

        1. Accept.

        2. If the diameter is less than in Step.

        1. Reject.

    4. SUBTASK 72-41-21-220-116 Examine the Stage 10 Rotor Path Ring Boltholes at Location 3

    1. Refer to Figure.

      2. Burred edges.

        1. Up to 0.002 in. (0.05 mm).

        1. Accept.

        2. More than in Step.

        1. Repair, VRS6098 TASK 72-41-21-300-015 (REPAIR-015).

      3. Scratched.

        1. Up to 0.002 in. (0.05 mm) in depth.

        1. Accept.

        2. More than in Step.

        1. Repair, VRS6098 TASK 72-41-21-300-015 (REPAIR-015).

    5. SUBTASK 72-41-21-220-117 Examine the Stage 10 Rotor Path Ring Grooves at Locations 1131 and 1134

    1. Refer to Figure.

      2. Scored.

        1. Up to 0.002 in. (0.05 mm) in depth.

        1. Accept.

        2. More than in Step.

        1. Reject.

      3. Galled.

        1. Up to 0.002 in. (0.05 mm) in depth.

        1. Accept.

        2. More than in Step.

        1. Reject.

      4. Location 1131.

        1. If the width of the groove is between 0.1350 in. and 0.1370 in. (3.43 mm and 3.48 mm).

        1. Accept.

        2. If the width of the groove is more than in Step.

        1. Reject.

      5. Location 1134.

        1. If the width of the groove is between 0.115 in. and 0.117 in. (2.93 mm and 2.98 mm).

        1. Accept.

        2. If the width of the groove is more than in Step.

        1. Reject.

    6. SUBTASK 72-41-21-220-118 Examine the Stage 10 Rotor Path Ring Location Dowel Hole at Location 1195

    1. Refer to Figure.

      2. Burred edges.

      1. Reject.

      3. Scratched.

      1. Reject.

        2. Location dowel hole diameter 1195.

          1. If the diameter is between 0.315 in. and 0.329 in. (8.00 mm and 8.36 mm).

          1. Accept.

          2. If the diameter is more than in Step.

          1. Reject.

    7. SUBTASK 72-41-21-220-119 Examine the Stage 10 Rotor Path Ring all Remaining Surfaces

      1. Nicked, dented and scratched.

        1. Up to 0.002 in. (0.05 mm) in depth.

        1. Accept.

        2. More than in Step.

        1. Repair, VRS6098 TASK 72-41-21-300-015 (REPAIR-015).

    8. Figure: Stage 10 rotor path ring - inspection locations

    Stage 10 rotor path ring - inspection locations

Requirements After Job Completion

Follow-On Conditions

NONE
Change Type:

Revised the procedure to update the limits for location 1110. (17VG178)