TASK 71-51-42-200-301 EEC Fan Harness And Igntion Supply Harness - Examine The Harness, Inspection-001

DMC:V2500-A0-71-51-4200-00A-310A-C|Issue No:002.00|Issue Date:2014-08-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 71-51-42-200-301 EEC Fan Harness And Igntion Supply Harness - Examine The Harness, Inspection-001

Effectivity

FIG/ITEM

PART NO.

01-005

740-5870-503

01-005

740-5870-9003

01-005

740-5870-505

01-005

740-5870-9005

01-005

740-5870-511

01-005

740-5870-9011

01-005

740-5870-513

01-005

740-5870-9013

01-005

745-5870-501

01-005

745-5870-503

General

The policy that is necessary for Inspection is given in SPM TASK 70-20-01-200-501.

All the parts must be cleaned before any part is examined, refer to Cleaning-000 TASK 71-51-42-100-300.

All the parts must be visually examined for damage, corrosion and wear. Any defects that are not identified in the procedure must be referred to IAE.

Do not discard the part until you are sure there are no repairs available. Refer to the instructions in Repair before a discarded part is used again or oversize parts are installed.

Parts which should be discarded can be held although no repair is available. The repair of a discarded part could be shown to be necessary at a later date.

Reference

Refer to the SPM for data on these items.

Definitions of Damage, SPM TASK 70-02-02-350-501.

Inspection of Parts, SPM TASK 70-20-00-200-501.

Repair Chafing to the Cable of the Electrical Harness, SPM TASK 70-35-25-300-001-E01.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

NONE

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 71-51-42-210-051 Examine the Connectors

      1. Cracked or broken

      1. Repair, VRS2980 (Repair-003),TASK 71-51-42-300-003.

      2. Coupling nuts

        1. Threads

          1. Pick-up, crossed or stripped

          1. Repair, VRS2980 (Repair-003),TASK 71-51-42-300-003.

      3. Contact pins

        1. Bent

        1. Repair, VRS2987 (Repair-004), TASK 71-51-42-300-004.

        2. Worn (do the check with a new socket)

        1. Repair, VRS2987 (Repair-004), TASK 71-51-42-300-004.

      4. Contact sockets

        1. Bent

        1. Repair, VRS2987 (Repair-004), TASK 71-51-42-300-004.

        2. Worn (do the check with a new pin)

        1. Repair, VRS2987 (Repair-004), TASK 71-51-42-300-004.

    2. SUBTASK 71-51-42-210-052 Examine the Cable

      1. Burned, frayed or fused.

      1. Repair, VRS2964 (Repair-001) TASK 71-51-42-300-001.

      2. Chafed

        1. Damage to the outer jacket only

        1. Refer to SPM, Repair-001 (VRS7002) TASK 70-35-25-300-001-E01.

        2. Damage more than limits given in Step

        1. Refer to Repair-001 (VRS2964) TASK 71-51-42-300-001.

      3. Loose

        1. Crimp the joints

        1. Refer to Repair-004 (VRS2987) TASK 71-51-42-300-004.

    3. SUBTASK 71-51-42-210-053 Examine the Ties

      1. Chafed or frayed

      1. Repair, VRS2972 (Repair-002) TASK 71-51-42-300-002.

Requirements After Job Completion

Follow-On Conditions

NONE
Change Type:

Modified the procedure to add Repair-001 reference. (14VN809)