TASK 72-00-32-450-012 LPC/Intermediate Case Module Components - Install The Stage 10 Air Solenoid Valve, Installation-019

DMC:V2500-A0-72-00-3250-11A-720A-B|Issue No:001.00|Issue Date:2014-05-01

Export Control

EAR Export Classification: Not subject to the EAR per 15 C.F.R. Chapter 1, Part 734.3(b)(3), except for the following Service Bulletins which are currently published as EAR Export Classification 9E991: SBE70-0992, SBE72-0483, SBE72-0580, SBE72-0588, SBE72-0640, SBE73-0209, SBE80-0024 and SBE80-0025.

Copyright

© IAE International Aero Engines AG (2001, 2014 - 2021) The information contained in this document is the property of © IAE International Aero Engines AG and may not be copied or used for any purpose other than that for which it is supplied without the express written authority of © IAE International Aero Engines AG. (This does not preclude use by engine and aircraft operators for normal instructional, maintenance or overhaul purposes.).

Applicability

All

Common Information

TASK 72-00-32-450-012 LPC/Intermediate Case Module Components - Install The Stage 10 Air Solenoid Valve, Installation-019

General

Fig/item numbers in parentheses in the procedure agree with those used in the IPC. Only the primary Fig/item numbers are used. For the service bulletin alpha variants refer to the IPC.

For all parts identified in a different Chapter/Section/Subject, the applicable Chapter/Section/Subject comes before the Fig/item number.

Lubricate all threads and abutment faces of nuts and bolts with CoMat 10-039 ENGINE OIL, unless other lubricants are referred to in the procedure.

Do not remove the special plastic caps from the electrical connectors and receptacles until immediately before they are connected. This will give protection from unwanted fluids or materials.

During the installation procedure make sure that the harnesses are held temporarily along their different lengths. This is to prevent too much strain on the harnesses, cables and electrical connectors.

For the data on the electrical connectors refer to the SPM TASK 70-43-00-400-501 and TASK 70-43-01-400-501.

For the torque tightening procedures, refer to the SPM TASK 70-41-00-400-501 and TASK 70-41-01-400-501.

Special torque data and assembly tolerances are included in this procedure.

Special torque data is identified with the symbol * after the torque value.

For lockwire data and procedures refer to the SPM TASK 70-42-05-400-501.

For safety cable data and procedures refer to the SPM TASK 70-42-08-400-501.

Safety the threaded fasteners in the ATA Chapter/Section/Subject 71-51-41 as applicable with CoMat 02-274 SAFETY CABLE KIT or CoMat 02-275 SAFETY CABLE KIT.

NOTE

To identify the consumable materials refer to the PCI.
SBE 70-0813 : Announcement of introduction of safety cable as a preferred method to lockwire.
Safety the threaded fasteners in this TASK with safety cable for the ATA Chapter/Section/Subject detailed in 2. General.

Preliminary Requirements

Pre-Conditions

NONE

Support Equipment

NONE

Consumables, Materials and Expendables

NameManufacturerPart Number / IdentificationQuantityRemark
CoMat 01-002 SOLVENT, DELETED.0AM53CoMat 01-002
CoMat 02-126 LOCKWIRELOCALCoMat 02-126
CoMat 02-159 LACING TAPELOCALCoMat 02-159
CoMat 02-274 SAFETY CABLE KITLOCALCoMat 02-274
CoMat 02-275 SAFETY CABLE KITLOCALCoMat 02-275
CoMat 10-039 ENGINE OILLOCALCoMat 10-039
CoMat 06-086 TIES18992CoMat 06-086

Spares

NONE

Safety Requirements

NONE

Procedure

    1. SUBTASK 72-00-32-450-056 Install the Stage 10 Air Solenoid Valve (36-11-57,01-100) (Pre SBE 75-0047 and SBE 75-0047)

    1. Refer to Figure, Figure and Figure.

    2. Pre SBE 75-0047: Install the solenoid valve to the bracket HPC Stage 7 Solenoid Valve (75-32-51, 01-160) with three bolts and the three washers STAGE 10 AIR SOLENOID VALVE (36-11-57, 01-102) and STAGE 10 AIR SOLENOID VALVE (36-11-57, 01-104). Torque the bolts to 36 to 45 lbf.in (4 to 5 Nm).

    3. SBE 75-0047: Install the solenoid valve to the bracket HPC Stage 7 Solenoid Valve (75-32-51, 01-160) with three bolts, the three washers and the nut STAGE 10 AIR SOLENOID VALVE (36-11-57, 01-102), STAGE 10 AIR SOLENOID VALVE (36-11-57, 01-104) and STAGE 10 AIR SOLENOID VALVE (36-11-57, 01-106). Torque the bolts to 36 to 45 lbf.in (4 to 5 Nm).

    4. Connect the tubes 148 and 151 to the solenoid valve unions, connect the tube 148 to the tube 149 (branch tube). Torque the tube nuts to 204 to 221 lbf.in (23 to 25 Nm). Safety the tube nuts with CoMat 02-126 LOCKWIRE.

    5. Tighten the clip bolt/nut made loose during the removal procedure (as necessary) to 36 to 45 lbf.in (4 to 5 Nm).

    6. Remove the CoMat 06-086 TIES which attach the electrical/harness connector 4029KS-A to the primary harness bundle. Connect the electrical connector to the solenoid valve receptacle. Torque the electrical connector to 18* lbf.in (2.0 Nm).

    7. Install the bolt, the washer and the nut at the clip position 1081. Torque the nut to 36 to 45 lbf.in (4 to 5 Nm).

    8. Attach the electrical harnesses together, as necessary, with CoMat 02-159 LACING TAPE. Refer to TASK 72-00-32-420-004.

    2. SUBTASK 72-00-32-210-067 Visually Inspect the Electrical Backshells and Cable Clamps

    1. Refer to Figure.

    2. Make sure that all the applicable connectors, backshells and cable clamps are secure.

    3. Make sure that all the applicable backshells and cable clamps are safetied with CoMat 02-126 LOCKWIRE. Refer to the SPM TASK 70-42-05-400-501.

    3. SUBTASK 72-00-32-210-068 Visually Inspect the EEC Harness (01-005) Electrical Backshells and Cable Clamps (SBE 70-0813)

    1. NOTE

      Use this procedure to safety the EEC harness backshells and cable clamps with safety cable.

      Refer to Figure.

    2. Make sure that all the EEC harness connectors, backshells and cable clamps are secure.

    3. Make sure that all the EEC harness backshells and cable clamps are safetied. Safety with CoMat 02-274 SAFETY CABLE KIT or with CoMat 02-275 SAFETY CABLE KIT. Refer to the SPM TASK 70-42-08-400-501.

    4. Figure: Pre SBE 75-0047: Install the Stage 10 Air Solenoid Valve

    Pre SBE 75-0047: Install the Stage 10 Air Solenoid Valve

    Figure: SBE 75-0047: Install the Stage 10 Air Solenoid Valve

    SBE 75-0047: Install the Stage 10 Air Solenoid Valve

    Figure: Install the Stage 10 Air Solenoid Valve

    Install the Stage 10 Air Solenoid Valve

    Figure: Visually Inspect the Backshells and Cable Clamps

    Visually Inspect the Backshells and Cable Clamps

Requirements After Job Completion

Follow-On Conditions

NONE
Manufacturer Code:0AM53
Enterprise Name:IAE INTERNATIONAL AERO ENGINES AG
BU Name:NULL
Building:SUITE 400
Street:628 HEBRON AVENUE
City:GLASTONBURY
State:CT
Zip Code:06033
Country:USA
Manufacturer Code:18992
Enterprise Name:HANSCOM INC
BU Name:HANSCOM INC
Street:331 MARKET STREET
P.O. Box:364
City:WARREN
State:RI
Zip Code:02885
Country:USA
Phone Number:1-401-247-1999, 1-800-725-6788
Fax Number:1-401-247-4575
Internet:www.hanscominc.com
Manufacturer Code:LOCAL
Enterprise Name:LOCALLY SUPPLIED
Manufacturer Code:X111X
Supply Number:CoMat 01-002
Type:sp01
Supply Short Name:CoMat 01-002 SOLVENT, DELETED.
Supply Name:CoMat 01-002 SOLVENT, DELETED.
Specification Groups:
Doc NumberType
wiring harnesses. Where CoMat 01‐002 is specified to clean mechanical components, use one or more of the solvents that SPM TASK 70‐11‐26‐300‐503 specifies as applicable.DELETED. Where CoMat 01‐002 is specified to clean electrical contacts or wiring harnesses, use one or more of the solvents that SPM TASK 70‐11‐57‐110‐501 specifies to clean electrical contacts or
Suppliers:
ManufacturerRemarks
X111X
Manufacturer Code:K6835
Supply Number:CoMat 02-126
Type:sp01
Supply Short Name:CoMat 02-126 LOCKWIRE
Supply Name:CoMat 02-126 LOCKWIRE
Specification Groups:
Doc NumberType
DTD 189A, 0.028 TO 0.032 IN DIA
Suppliers:
ManufacturerRemarks
K6835
KB362
LOCAL
U06C8
Manufacturer Code:LOCAL
Supply Number:CoMat 02-159
Type:sp01
Supply Short Name:CoMat 02-159 LACING TAPE
Supply Name:CoMat 02-159 LACING TAPE
Specification Groups:
Doc NumberType
T085 OMAT: 274
Suppliers:
ManufacturerRemarks
LOCAL
IE218
K6835
Manufacturer Code:LOCAL
Supply Number:CoMat 02-274
Type:sp01
Supply Short Name:CoMat 02-274 SAFETY CABLE KIT
Supply Name:CoMat 02-274 SAFETY CABLE KIT
Specification Groups:
Doc NumberType
SAE AS3510-0218K (DIA 0,032 IN LENGTH 18IN)
Suppliers:
ManufacturerRemarks
LOCAL
11851
U0419
70958
H7503
SA221
V384V
Manufacturer Code:X111X
Supply Number:CoMat 02-275
Type:sp01
Supply Short Name:CoMat 02-275 SAFETY CABLE KIT
Supply Name:CoMat 02-275 SAFETY CABLE KIT
Specification Groups:
Doc NumberType
Deleted. Use CoMat 02-274.
Suppliers:
ManufacturerRemarks
X111X
Manufacturer Code:18992
Supply Number:CoMat 06-086
Type:sp01
Supply Short Name:CoMat 06-086 TIES
Supply Name:CoMat 06-086 TIES
Specification Groups:
Doc NumberType
PMC 4272SPECIAL WIRE TIES
Suppliers:
ManufacturerRemarks
18992
Manufacturer Code:LOCAL
Supply Number:CoMat 10-039
Type:sp01
Supply Short Name:
Supply Name:CoMat 10-039 ENGINE OIL
Specification Groups:
Doc NumberType
DELETED
Suppliers:
ManufacturerRemarks
LOCAL